AR-M351U, AR-M451U (serv.man17). Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 9

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 9

(Built-in finisher)

(Console finisher)

( ) : Added when the punch unit is installed.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press START key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the
load.

Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key. (The entered value is stored.)

3-3

Operation test/Check

Used to check the operation of the load in the 
finisher and the control circuit.

Finisher

Operation

Built-in finisher

1

T2S

Tray 2 solenoid

2

T2OM

Paper exit motor

3

SPS

Stopper solenoid

4

SCRS

Roller pressure release solenoid

5

PPS

Rear edge h folding solenoid

6

SCGS

Compiler gate solenoid

7

STTM

Staple rotation motor

8

STUM

Stapler shift motor

9

MM

Main drive motor

10

EVM

Elevator motor

11

STM

Staple motor

12

JRM

Jogger motor rear

13

JFM

Jogger motor front

14

PSM

Pusher motor

Console finisher

1

FFC

Folding clutch

2

FPSM

Puncher side register motor

3

FPNM

Punch motor

4

FLM

Shift  motor

5

FFSM

Stapler motor

6

FSM

Slide motor

7

FRJM

Alignment motor R

8

FFJM

Alignment motor F

9

FAM

Bundle exit motor

10

FPM

Paddle motor

11

FFM

Transport motor

SIMULATION 3-3

FINISHER SENSOR CHECK.

PID           SCID         SCID2         PPD

SCPD          POD          T1PF          T2UP

T2DN          T2PD         STSP          STLS

STNC          STHP         JFHP          JRHP

PSHP          STUHP        STTHP1

STTHP2        DOPD         DSW1          DSW2

24VM          MMLK

SIMULATION 3-2

FINISHER SENSOR CHECK.

FSSS  FJS     FFDSW  FTCS    FFDS 

FSPS  FSUC    FSS    FSTHPS  FSHPS   FLE     FLLLS

FULS  FFE     FFES   FFRHPS  FFHPS   FFPS    FSLS

FBES  FOBHPS  FAS    FRJHPS  FFJHPS  FARHPS  FPHPS

FES

(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)

(FPDSS1)(FPTS)

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

3-6

Adjustment

Used to adjust the stacking capacity of the 
finisher. (Used to adjust the alignment plate 
(jogger) stop position in the finisher paper width 
direction. The adjustment is made by changing the 
alignment plate home position in the paper width 
direction by software.)

Finisher

Operation

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.
Stops when the operation is terminated.

3-10

Adjustment

Console finisher (AR-FN7) adjustment

Finisher

Operation

Item

Set 

range

Initial 
value

1STEP

1

Saddle binding position 
adjustment

0 - 400

200

0.0707mm

2

Saddle folding position 
adjustment

0 - 400

200

0.0525mm

3

Front alignment position 
adjustment

0 - 20

10

0.367mm

4

Rear alignment position 
adjustment

0 - 20

10

0.367mm

SIMULATION 3-3

FINISHER LOAD TEST. SELECT 1-

AND PRESS START.

2

SIMULATION 3-3

FINISHER LOAD TEST. EXECUTING

.

2

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.

50

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. MOVING....

50