AR-M351U, AR-M451U (serv.man17). Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 5

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 5

46

18

Used to adjust the gamma (density gradient) in 
the copy mode.

19

Used to set the auto mode operation 
specifications in each mode (copy, scan, FAX).

20

Used to adjust the copy density correction in the 
SPF copy mode for the document table copy 
mode. The adjustment is made so that the copy 
density becomes the same as that of the 
document table copy mode.

21

Used to adjust the scanner exposure level in all 
the scanner modes.

22

Used to adjust the scanner exposure level in the 
normal text mode.

23

Used to adjust the scanner exposure level in the 
fine text mode.

24

Used to adjust the scanner exposure level (in the 
super fine text mode).

25

Used to adjust the scanner exposure level in the 
ultra fine text mode.

27

Used to adjust the gamma (density gradient) of 
the network scanner mode.

31

Used to adjust sharpness of the copy mode.

39

Used to adjust sharpness of the FAX mode.

45

Used to adjust the image density in the FAX 
mode (600dpi).

46

48

1

Used to adjust the copy magnification ratio (in the 
main scanning and the sub scanning directions).

5

Used to adjust the copy magnification ratio in the 
sub scanning direction.

6

50

1

Used to adjust the copy image position and the 
void area (image loss) adjustment on print paper 
in the copy mode. (The similar adjustment can be 
performed with SIM 50-5 and 50-2 (Simplified 
method).) (Document table mode)

2

Used to adjust the document scan position, the 
image print position, and the void area (image 
loss). (Simple adjustment) (This adjustment is the 
simple method of SIM 50-1.) (Document table 
mode)

5

Used to adjust the print image position and the 
void area (image loss) on print paper. 
(Adjustment as the print engine) (This adjustment 
is reflected on all the FAX/printer/copy modes.)

6

Used to adjust the copy image position and void 
area (image loss) on print paper in the copy 
mode. (The similar adjustment can be performed 
with SIM 50-7 (simple method).) (SPF mode)

7

Used to adjust the copy image position and void 
area (image loss) on print paper in the copy 
mode. (The similar adjustment can be performed 
with SIM 50-6.) (SPF mode)

10

Used to adjust the print image off-center position. 
(Adjusted separately for each paper feed 
section.)

12

Used to adjust the scan image off-center position. 
(Adjusted separately for each scan mode.)

27

Used to adjust the image loss of the scan image 
in the FAX/scan mode.

51

2

Used to adjust the contact pressure of paper on 
the resist roller of each section (each paper feed, 
duplex feed and SPF paper feed of the copier). 
(This adjustment is required when the print image 
position variations are considerably great or when 
paper jams occur frequently.)

Code

Function (Purpose)

Main

Sub

53

6

Used to adjust the DSPF width detection level.

7

Used to enter the SPF width detection adjustment 
value.

8

Used to adjust the document scan start position. 
(Used to adjust the scanner scan position in the 
SPF mode front scan.)

55

1

Used to set the specifications of the engine 
control operations. (PCU PWB)

2

Used to set the specifications of the scanner 
control operations. (Scanner control PWB)

3

Used to set the specifications of the controller 
operations. (MFP control PWB)

56

1

Used to transfer the MFP controller data. (Used to 
repair the PWB.)

60

1

Used to check the MFP control (DRAM) 
operations (read/write).

61

1

Used to check the operation of the scanner (write) 
unit (LSU).

2

Used to adjust the laser power (absolute value) in 
the copy mode. 

3

Used to adjust the laser power (absolute value) in 
the FAX mode.

4

Used to adjust the laser power (absolute value) in 
the printer mode. 

62

1

Used to format the hard disk. (Only in the model 
with a disk installed)

2

Used to check the operation of the hard disk 
(read/write). (Only in the model with a disk 
installed) (Partial check)

3

Used to check the operation of the hard disk 
(read/write). (Only in the model with a disk 
installed) (All areas check)

6

Used to check the operations of the hard disk. 
(The self diag operation of the SMART function is 
executed.) (Only in the model with a disk 
installed)

7

Used to check the operations of the hard disk. 
(The result of the self diag operation of the 
SMART function is printed out.) (Only in the 
model with a disk installed)

8

Used to format the hard disk (the system area 
excluded). (Only in the model with a disk 
installed)

10

Used to delete a job complete list (also to delete 
job log data) (Only in the model with a disk 
installed)

11

Used to delete document filing data. (The 
management area (standard folder, user folder) is 
cleared.) (Only in the model with a disk installed)

63

1

Used to check the result of shading correction. 
(The shading correction data are displayed.)

2

Used to execute shading.

7

Used to adjust the white plate scan start position 
for shading. (Document table mode)

64

1

Used to check the operation of the printer section 
(self-print operation), (The print pattern, the paper 
feed mode, the print mode, the print quantity, and 
the density can be optionally set.)

65

1

Used to adjust the touch panel (LCD display 
section) detection position.

2

Used to check the result of the touch panel (LCD 
display) detection position adjustment. (The 
coordinates are displayed.)

66

1

Code

Function (Purpose)

Main

Sub