AR-M351U, AR-M451U (serv.man17). Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 13

Read Sharp AR-M351U / AR-M451U (serv.man17) Service Manual online

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 13
*1: Displayed when OPTION of multi-purpose only.
*2: Displayed when manual feed OPTION is added.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 operates.
Press [CUSTOM SETTINGS] key to stop the operation.
Operation/Procedure
1) Select the number corresponding to the operating condition of
aging with 10-key.
The combined mode of 0 - 6 mode and 10, 20, or 30 mode can
be set.
In that case, the number corresponding to one of 0 - 6 mode
and the number corresponding to one of 10, 10, and 30 mode
are added and the sum number is entered.
2) Press [START] key.
The condition selected in procedure 1) is set.
The setting of this simulation is kept valid until the power is turned
off.
18*1
MCLUM
MP tray lift-up motor signal
19*2
MPFS
Manual paper feed solenoid signal
20*2
MPFC
 Manual paper feed clutch signal
21*2
MSS
 Manual paper feed gate solenoid
Press [START] key, and the 
operation is started.
Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 
repeating the operation several times.
6-2
Purpose
Operation test/Check
Function
(Purpose)
Used to check the operations of each fan motor 
and its control circuit.
Section
Other
Item
Operation
1
Fan motor high speed
2
Fan motor low speed
3
Cooling fan motor (Controller/HDD) 
Press [START] key, and the operation 
is started.
Press [CUSTOM SETTINGS] key, and 
the operation is stopped.
SIMULATION 6-1
FEED OUTPUT CHECK. SELECT 1-22, AND PRESS START.
1.MSWPR  2.HLPR 3.DCPR 4.MM   5.DM  6.DSB_FW
7.DSB_RV 8.CPFC 9.RRC  10.TRC 11.FGS_FIN
12.LUM   13.TRC_DSK    14.PSPS
15.MCM   16.MCPCL      17.MCFCL 18.MCLUM
19.MPFS  20. MPFC      21.MSS   22.MSWS
  2
SIMULATION 6-1
FEED OUTPUT CHECK. EXECUTING....
1.MSWPR  2.HLPR 3.DCPR 4.MM   5.DM  6.DSB_FW
7.DSB_RV 8.CPFC 9.RRC  10.TRC 11.FGS_FIN
12.LUM   13.TRC_DSK    14.PSPS
15.MCM   16.MCPCL      17.MCFCL 18.MCLUM
19.MPFS  20.MPFC       21.MSS   22.MSWS
  2
SIMULATION 6-2
FAN MOTOR CHECK. SELECT 1-3, AND PRESS START.
1.FMHi
2.FMLo
3.CFM-ICU/HDD
  2
SIMULATION 6-2
FAN MOTOR CHECK..
2.FMLo
  2
7
7-1
Purpose
Setting
Function
(Purpose)
Used to set the operating conditions of aging.
Section
Item
Operation
0
NO MISS FEED DETECTION No jam detection
1
AGING
Aging mode
2
AGING/NO MISS FEED 
DETECTION.
No jam detection, aging 
mode
3
AGING/NO MISS FEED 
DETECTION/NO WARM UP/
NO TEMPERATURE 
CONTROL.
No jam detection/ no warm-
up/ no fusing temperature 
control, aging mode
4
NO WARM UP.
No warm-up 
5
AGING/INTERVAL.
Intermittent aging mode
6
AGING/INTERVAL/NO MISS 
FEED DETECTION.
No jam detection 
intermittent aging mode
+10 NO PROCESS UNIT CHECK. Above +10: No process unit 
(including the developing 
unit) detection
+20 NO SHADING.
Above +20: No shading
+30 NO PROCESS UNIT CHECK/
NO SHADING.
Above +30: No process unit 
detection /no shading
Press [START] key to start registration and operation. 
The operation mode is kept until the power is turned off or setting is made again. 
SIMULATION 7-1
AGING TEST SETTING. SELECT 0-36, AND PRESS START.
0.NO MISS FEED DETECTION
1.AGING
2.AGING/NO MISS FEED DETECTION.
3.AGING/NO MISS FEED DETECTION/
  NO WARM UP/NO TEMPERATURE CONTROL.
4.NO WARM UP.
5.AGING/INTERVAL.
6.AGING/INTERVAL/NO MISS FEED DETECTION.
+10:NO PROCESS UNIT CHECK.
+20:NO SHADING.
+30:NO PROCESS UNIT CHECK/NO SHADING.
    2
Display
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.
Random: