AR-C270 (serv.man13). (Section 8) Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 5

Code

Function (Purpose)

Purpose

Section

Item

Main

Sub

24

7

Used to clear the OPC drum (membrane
decrease) correction counter. (Performed
when the OPC drum is replaced.)

Data clear

Image process
(Photoconductor/
Developing/Transfer/
Cleaning)

Photo
conductor

Counter

Photo conductor

8

Used to clear the waste toner counter in the
transfer section.

Data clear

Image process
(Photoconductor/
Developing/Transfer/
Cleaning)

Copy

Counter

9

Used to clear the self print and the list print
counter. "(After completion of maintenance,
this counter is cleared.
(AR-C150/C250/C160/C270)

Data clear

Printer

Counter

Printer

25

1

Used to check the operation of the main
drive (excluding the scanner section) and the
toner density sensor. (The toner density
sensor output can be monitored.)

Operation test/check

Image process
(Photoconductor/
Developing/Transfer/
Cleaning)

Developer/
Toner Hopper

Operation

2

Used to make the initial setup (automatic
adjustment) of toner density when replacing
developer.

Setting

Image process
(Photoconductor/
Developing/Transfer/
Cleaning)

Developer/
Toner Hopper

26

1

Used to make option setup. (When installing
an option, this simulation is used to setup for
that option (software).
(AR-C150/C250/C160/C270)

Setting

Specifications

Options

2

1) Used to set the paper size of the large
capacity tray. (When the paper size is
changed, the software setup must be
changed accordingly with this simulation.)
2) Used to detect 8.5 

×

 13 (INCH Series)

paper or documents and to set the display
mode. (All paper feed modes)
3) Used to set the display form of the paper
kind in the manual paper feed mode.

Setting

Paper transport

Specifications

3

Used to set the auditor specification mode.
Setting must be made according to the use
conditions of the auditor.

Setting

Auditor

Specifications

5

Used to set the count mode of the total
counter, the developer counter, and the
maintenance counter.

Setting

Specifications

Counter

6

1)Used to set the specifications (paper, fixed
copy magnification ratio, machine operations
in case of an image (process) correction
error) according to the destination.
(AR-C150/C250/C160/C270)
2) Used to set the user logo. (AR-C100 only)

Setting

Specifications

Destination

18

Used to set YES/NO of toner save operation.
(This simulation is valid only for Japan and
UK versions. It depends on Sim 26-6
(Destination) setting. For the other
destinations, the same setting can be made
by the user program P22. (Effective only in
the monochrome copy mode)

Setting

Specifications

Operation mode
(Common)

22

Used to set the specification (language) for
the destination. (AR-C150/C250/C160/C270)

Setting

Specifications

Language

28

Used to set the AC power voltage. (For
control of the fusing section heater lamp)

Setting

Power supply
(DC/AC/High)

Operation

30

Used to set the CE mark complying
operation mode. (Conforms to the soft start
when driving the fusing heater lamp.)

Setting

Fixing (Fusing)

Specifications

Operation mode
(Common)

32

Used to set the fan rotating speed. (low
speed)

Setting

Operation

35

Used to set whether the trouble history
display by SIM 22-4 is displayed as one
trouble or as the accumulated number of
continuous troubles when two or more
troubles of same kind occur continuously.

Setting

Specifications

45

Used to set the copy charge. (AR-C100 only)

Setting

Specifications

Others

52

Used to set YES/NO of count up of non-copy
paper (cover or insertion paper).

Setting

Specification

Operation mode

53

Used by the user to set Enable/Disable auto
color calibration (auto adjustment of color
balance and density)

setting

Specifications

Operation mode

54

Used to adjust the brightness of LCD display.
(AR-C250 only)

Adjustment

LCD display

Operation

8 –  5