Read Sharp AR-C170 (serv.man31) Service Manual online
AR-C170M PRINTER CONTROLLER SECTION 14 - 25
(5) Connect the cable to the printer control PWB unit.
Connect t the Centro cable, the USB cable, and the LAN cable to
the printer control PWB unit connectors.
the printer control PWB unit connectors.
(6) Turn ON the main switch of the printer.
Insert the power plug of the printer into the power outlet.
Turn ON the main switch on the rear side of the printer.
(7) Check the operation.
Check to insure that the scanner function (trial mode) operates
normally.
normally.
12. AR-NS2 installing procedure
The scanner expansion board (AR-EB8) and the expansion
memory module (256MB or more) are required to use the scanner
expansion kit.
memory module (256MB or more) are required to use the scanner
expansion kit.
For installing procedures and the memory capacity, refer to the
descriptions below.
descriptions below.
To enable the scanner function, the product key must be acquired.
1) Check the capacity of the Printer PWB memory.
Print the printer setting list by the key operation of the main
unit operation panel.
unit operation panel.
Check to confirm that the expansion memory is 256MB or
above.
above.
2) Prepare for use of the network scanner function.
To enable the system configuration, enter the product key with
the user program.
the user program.
Use the 10-key to display the acquired product key on the
LCD, and press [OK] key.
LCD, and press [OK] key.
The LCD displays "SCANNER KEY OK."
Setting of the product key is complete. To update the system,
press the [CA] key to exit the setting mode.
press the [CA] key to exit the setting mode.
3) Paste the label.
Attach the document indication label (orientation indication
label) B to the RSPF.
label) B to the RSPF.
∗
Do not use the document indication label (orientation indication
label) A.
label) A.
13. AR-PK4 installing procedures
A. General
To install the PS kit (AR-PK4), follow the procedures below.
1) Install the PS firmware ROM.
2) Enter the PS expansion kit product key.
3) Install the PS font.
4) Install the PS printer utility software.
B. Check items
The following items must be prepared for use of the AR-PK4.
• PS firmware ROM (standard accessory of the AR-PK4)
• CD-ROM with the PS printer utility software in it (standard
accessory of the AR-PK4)
• PS expansion kit product key
• Hard disk unit (Must be installed to the main unit.)
• ROM's of the late version as shown below (the following ver-
sions or later)
BOOT: 1.9
PCL: 5.1x
ICU: 5.15
PCU: V5.09
SCN: 5.08
OPE: 5.14
Use SIM 22-5 to check that each version is as shown above or
later one.
later one.
• 512MB of expansion memory is required. (Plus 128MB of
onboard memory, total 640MB.)
C. PS firmware ROM installation
1) Turn off the main unit power.
2) Remove the printer controller PWB.
3) Install the PS firmware ROM to the printer controller PWB
[CODE-3] slot.
(There are the boot ROM, the program (PCL) ROM, the font
ROM, and the PS ROM in this order from outside of the PWB.)
ROM, and the PS ROM in this order from outside of the PWB.)
4) If the capacity of expansion memory is insufficient, expand
512MB memory. (640MB in total, together with 128MB of
onboard memory).
onboard memory).
5) If the hard disk is not installed, install it to the main unit.
6) Install the printer controller PWB to the main unit.
7) Turn on the main unit power.
8) Enter the PS expansion kit product key in the key operator
program mode.
9) Reboot the main unit.
10) After the main unit goes into the print ready state, use SIM 22-
5 to check that the PS firmware version is displayed.
Orientation indication label A
Orientation indication label B
Orientation indication label B
Click on the first or last page to see other AR-C170 (serv.man31) service manuals if exist.