Read Sharp AR-C170 (serv.man31) Service Manual online
AR-C170M PRINTER CONTROLLER SECTION 14 - 18
B. Details
1: When set to enable, the easy calibration, test print, and color
balance cannot be performed in the color adjustment of printer
setting of key operation.
setting of key operation.
(Items to be selected)
*1: When SIM 50-20 is used to adjust the image resist to the best
and the image resist adjustment is performed under the
following condition automatically, the best adjustment state
may be changed. To avoid this, set the adjustment item AR to
Disable.
following condition automatically, the best adjustment state
may be changed. To avoid this, set the adjustment item AR to
Disable.
When the adjustment item AR is set to Disable (ON), the
image resist adjustment is automatically performed under the
following conditions.
image resist adjustment is automatically performed under the
following conditions.
Normally set to ON condition.
*2: When the image registration automatic adjustment operation
is abnormal, it is judged as an error or not.
• After replacement of a toner cartridge
At every 8000 copies (total of print and copy)
(When, however, 8000 copies is reached during a job, the
operation is stopped after completion of the job.)
(When, however, 8000 copies is reached during a job, the
operation is stopped after completion of the job.)
26
26
-54
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of auto color calibration
for the printer.
for the printer.
Item
Specifications
Operation mode
Operation/
Procedure
Procedure
1. Select Enable or Disable with the 10-key.
Disable 0: YES
Enable 1: NO
Enable 1: NO
2. Press the [OK] key.
Set
value
Content
Default
0
Disable auto color calibration (automatic
adjustment of printer color balance and
density)
adjustment of printer color balance and
density)
1
1
Enable auto color calibration (automatic
adjustment of printer color balance and
density)
adjustment of printer color balance and
density)
44
44
-1
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set enable/disable of correction operations
in the image forming (process) section.
in the image forming (process) section.
Section
Process (Photoconductor, developing, transfer,
cleaning)
cleaning)
Item
Operation
Operation/
Procedure
Procedure
1. Select the process item to enable the operation.
2. Press the [EXECUTE] key. (The operations of all
2. Press the [EXECUTE] key. (The operations of all
process items must be enabled.)
Display
Content
HV
Image forming section correction (Process
correction)
(High-density image density correction)
correction)
(High-density image density correction)
HT
Half-tone image density correction
HT (PRT)
Half-tone image density correction (Printer)
TC
Transfer output correction
RRM
RRM speed correction
MD
Photoconductor membrane decrease (sensitivity/
potential) correction
potential) correction
MD
(PRT_BK)
(PRT_BK)
Photoconductor membrane decrease (sensitivity/
potential) correction (Printer: monochrome)
potential) correction (Printer: monochrome)
AR
Image resist auto adjustment *1
AR CHK
Image resist auto adjustment error judgment YES/
NO *2
NO *2
67
67
-01
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operations of printer DRAM read/
write.
write.
Section
Printer
Item
Operation
Operation/
Procedure
Procedure
When the machine enters the simulation mode, the
printer DRAM read/write operation check is started.
After completion of check, "ERROR" or "MEMORY
SIZE" is displayed. If no memory is installed, "NA" is
displayed.
printer DRAM read/write operation check is started.
After completion of check, "ERROR" or "MEMORY
SIZE" is displayed. If no memory is installed, "NA" is
displayed.
67
-11
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the printer parallel I/F SELECT IN
signal.
signal.
Section
Printer
Item
Operation
Operation/
Procedure
Procedure
Enter the set value with the 10-key, and press the
[OK] key.
When a trouble occurs in communication between
PC and the printer by use of the printer parallel I/F,
change the setup content of this simulation.
[OK] key.
When a trouble occurs in communication between
PC and the printer by use of the printer parallel I/F,
change the setup content of this simulation.
Display
Content
Set range
Default
A
SELECT-IN
(0:OFF 1:ON)
(0:OFF 1:ON)
Centro I/F SELECT IN
signal YES/NO setting
signal YES/NO setting
0 – 1
1
Click on the first or last page to see other AR-C170 (serv.man31) service manuals if exist.