Read Sharp AR-505 (serv.man9) Service Manual online
3. Press the [OK] key or the PRINT button.
The value entered in procedure 2 is set.
When the PRINT key is pressed, copying is performed.
When the PRINT key is pressed, copying is performed.
(Note)
When a set value (density adjustment value in density
level 3) in the left column of the table below is changed
with this simulation, the set value (the overall density
level set value) in the right column is changed
accordingly.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode.
The result of adjustment by the simulation executed at
the last is reflected in actual printing.
The print density is normally adjusted by SIM 46-2.
To customize the print density for the density level
display value according to the user’s request, use the
simulation in the right column. (Excluding auto mode)
level 3) in the left column of the table below is changed
with this simulation, the set value (the overall density
level set value) in the right column is changed
accordingly.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode.
The result of adjustment by the simulation executed at
the last is reflected in actual printing.
The print density is normally adjusted by SIM 46-2.
To customize the print density for the density level
display value according to the user’s request, use the
simulation in the right column. (Excluding auto mode)
(AR-230/280/285/330/335 series)
Binary mode
Set with SIM 46-2.
Parameter to be changed
Linked simulation data
AE3.0 (AE)
CH3.0 (Character)
CH3.0 (Character)
Sim 46-9
MIX3.0 (Character/Photo)
Sim 46-10
PH3.0
(Photo) Sim
46-11
Default: 100
(AR-2X1/3X1/4XX/250/XX6 series)
Set with SIM 46-2.
Parameter to be changed
Linked simulation data
A
AE3.0 (AE)
B
CH3.0 (Character)
Sim 46-9
C
MIX3.0 (Character/Photo)
Sim 46-10
D
PH3.0 (2)
Sim 46-11 (Photo error
diffusion)
diffusion)
E
PH3.0 (256)
Sim 46-7 (Photo multi
value dither) (Japan only)
value dither) (Japan only)
∗
For EX, the above value E is disabled.
(AR-501/505)
Set with SIM 46-2.
Parameter to be changed
Linked simulation data
A
AE3.0 (AE)
B
CH3.0 (Character)
Sim 46-9
C
MIX3.0 (Character/Photo)
Sim 46-10
D
PH3.0 (2)
Sim 46-11 (Photo error
diffusion)
diffusion)
46 - 3
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the copy density in the copy mode (multi
value-auto, character and photo, photo mode).
(The overall print density in each mode (all of the speci-
fied density set for each density level (display value))
can be adjusted in each mode.)
(AR-250/280/285/330/335 only) (Japan only)
value-auto, character and photo, photo mode).
(The overall print density in each mode (all of the speci-
fied density set for each density level (display value))
can be adjusted in each mode.)
(AR-250/280/285/330/335 only) (Japan only)
Item
Picture quality
Density
Operation/
Procedure
Procedure
1. Select the print mode with [
↑
], [
↓
] key.
(The set value is highlighted.)
2. Enter the adjustment value with the 10-key.
3. Press the [OK] key or the PRINT button. (The value entered in
procedure 2 is set.) When the PRINT button is pressed, copy-
ing is performed.
ing is performed.
(Note)
When a set value (density adjustment value in density
level 3) in the left column of the table below is changed
with this simulation, the set value (the overall density
level set value) in the right column is changed
accordingly.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode. The result of adjustment by the
simulation executed at the last is reflected in actual
printing.
The print density is normally adjusted by SIM 46-2.
To customize the print density for the density level
display value according to the user’s request, use the
simulation in the right column. (Excluding auto mode/SIM
46-4.)
level 3) in the left column of the table below is changed
with this simulation, the set value (the overall density
level set value) in the right column is changed
accordingly.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode.
The parameters of the right and the left simulations and
their adjustment items are the adjustment values in the
same print mode. The result of adjustment by the
simulation executed at the last is reflected in actual
printing.
The print density is normally adjusted by SIM 46-2.
To customize the print density for the density level
display value according to the user’s request, use the
simulation in the right column. (Excluding auto mode/SIM
46-4.)
(Multi value mode)
Sim46-3 Parameter
set/changed by SM 46-3
Linked simulation data
AE3.0 (AE)
CH3.0(Character) Sim46-5
MIX3.0(Character/photo)
CH3.0(Character) Sim46-5
MIX3.0(Character/photo)
Sim46-6
PH3.0(Photo)
Sim46-7
Default: 100
AR-505
7 – 35
8/6/1999
Click on the first or last page to see other AR-505 (serv.man9) service manuals if exist.