Read Panasonic KX-TCD951GB / KX-TCD955GC Service Manual online
59
KX-TCD951GB/KX-TCD955GC
0082..0082
00
TAM_FLAGS
Configuration of TAM module.
bit 0 : TAM enbled (1).
bit 1 : Pocket Money enbled (1).
bit 0 : TAM enbled (1).
bit 1 : Pocket Money enbled (1).
0083..0083
00
BarredHsFlags
Indicates which HS are BARRED. Bit x = 1 = HS x is
barred.
barred.
0084..00C5
00
TaschenGeldFlags to
SoftRxSuppTimeout
SoftRxSuppTimeout
00C6..00C8
0D 1E 00
TaschenGeldFlags to
SoftRxSuppTimeout
SoftRxSuppTimeout
00C9..00C9
00
ChargePulseIntMode
00 using tonecounter in chargepulse detection
00CA..00CA
00
ClipRecognition
CLIP recognition configuration
0 : DTMF before 1. ring
1 : FSK before and after 1. ring
2 : DTMF before 1. ring and FSK after 1. ring
0 : DTMF before 1. ring
1 : FSK before and after 1. ring
2 : DTMF before 1. ring and FSK after 1. ring
00CB..00CB
08
DtmfDetectSens
Sensitivity for DTMF tone detection
00CC..00CC
09
Unused
Unused
00CD..00CD
FF
CasDetectSens
CAS detection sensitivity
00CE..00CE
00
DtmfClipConfig
Bit pattern defining DTMF CLIP configuration
Bit 0: Use polarity detection: 0=off, 1=on
Bit 1: Switch in line impedance in CLIP state: 0=off,
1=on
Bit 2,3: 00: Calling Party Number only (CPN).
01: Last Forwarding Number (LFN) if CPN is not
available.
10: Last Forwarding Number only (LFN).
11: CPN if LFN is not available.
Bit 4: Disconnect call on Polarity switch to normal
(TAD): 0=off, 1=on
Bit 5: Unused
Bit 6: Unused
Bit 7: Temporary used for Bus log enable/disable
Bit 0: Use polarity detection: 0=off, 1=on
Bit 1: Switch in line impedance in CLIP state: 0=off,
1=on
Bit 2,3: 00: Calling Party Number only (CPN).
01: Last Forwarding Number (LFN) if CPN is not
available.
10: Last Forwarding Number only (LFN).
11: CPN if LFN is not available.
Bit 4: Disconnect call on Polarity switch to normal
(TAD): 0=off, 1=on
Bit 5: Unused
Bit 6: Unused
Bit 7: Temporary used for Bus log enable/disable
00CF..00CF
FF
DtmfClipTone12
Bit pattern defining DTMF CLIP start tones
Bit 0-3: Start of Last Forwarding Number (LFN)
Bit 4-7: Start of Calling Party Number (CPN)
Bit 0-3: Start of Last Forwarding Number (LFN)
Bit 4-7: Start of Calling Party Number (CPN)
00D0..00D0
FF
DtmfClipTone34
Bit pattern defining DTMF CLIP start tones
Bit 0-3: Stop tone
Bit 4-7: Start of 'Reason' Number
Bit 0-3: Stop tone
Bit 4-7: Start of 'Reason' Number
00D1..00D1
64
DtmfClipPolToDtmf
Timeout
Timeout
The max time from polarity reversal to start of DTMF
tones
Unit: 10 secs
tones
Unit: 10 secs
00D2..00D2
32
DtmfClipInterdigit
Timeout
Timeout
The max time between two DTMF tones in the CLIP
Unit: 10 secs
Unit: 10 secs
00D3..00D3
C8
DtmfClipDtmfToRing
Timeout
Timeout
The max time from end of DTMF tones to ring start
Unit: 10 secs
Unit: 10 secs
00D4..00D4
18
DtmfClipBufSize to
FB2_e
FB2_e
The maximum number of DTMF digits to detect
00D5..00FF
00
DtmfClipBufSize to
FB2_e
FB2_e
The maximum number of DTMF digits to detect
0100..0117
FF
BarredPrefix1 to
BarredPrefix6_3
BarredPrefix6_3
Barred prefixes used in base programming. The prefix
is BCD coded with first
cipher first and unused variables are filled with F.
Ex: to activate barring on phonenumbers starting with
123, the contents of
is BCD coded with first
cipher first and unused variables are filled with F.
Ex: to activate barring on phonenumbers starting with
123, the contents of
Click on the first or last page to see other KX-TCD951GB / KX-TCD955GC service manuals if exist.