Read Panasonic AW-E600E Service Manual online
6
8
Adjust R701 so that signal level at E201 becomes clip at
1.2 Vp-p as shown in Fig. 4-5.
Fig. 4-5
8
Adjust R705 so that signal level at E101 becomes
coincides at signal level at E201 as shown in Fig. 4-6.
8
Change the connection of the CH2 of the Oscilloscope to
E301 on the Preprocess Board.
8
Adjust R707 so that signal level at E301 becomes
coincides at signal level at E201 as shown in Fig. 4-6.
Fig. 4-6
(5). Automatic Adjustment
Test Point:
E201 (G-IN)
Preprocess Board
8
Set the Lens Iris to the Automatic side.
8
Turn the power ON while pressing the ITEM/AWC Switch
YES/ABC Switch and No/BAR Switch on the Rear Panel
of the AW-E600E.
8
The Automatic Adjustment Menu is displayed, set the
Lens Iris to the Manual side.
8
Connect the Oscilloscope to E201 on the Preprocess
Board.
8
Set the Lens Iris so that the peak level of the Gray Scale
from the Blanking level becomes 300 mVp-p as shown in
Fig. 4-3.
8
Press the YES/ABC Switch.
8
Move to the Automatic Adjustment Item by the Item/AWC
Switch.
8
Set the Lens Iris to the Automatic side.
8
Press the YES/ABC Switch, and confirm that the
Automatic Adjustment should be finished and displayed
"OK".
8
Turn the power OFF and ON again so that the Camera
return to the Normal mode.
1.2 Vp-p
Adjust R705 or R707
so that the signal level
becomes coincide at
the signal level at E201.
so that the signal level
becomes coincide at
the signal level at E201.
(6).1. Manual Blemish Concealment and
Correction
Test Point:
Video Output Connector
Rear Panel
Adjust:
PAGE Button
Remote Control Box
ITEM Button
Remote Control Box
UP Button
Remote Control Box
DOWN Button
Remote Control Box
8
Set the Colour Bar Switch of the Remote Control Box to
the Camera side.
8
Turn the power ON while pressing the ITEM/AWC Switch
and No/BAR Switch on the Rear Panel of the AW-E600E.
8
The Menu will be displayed as shown Fig. 4-7 after
execute the Scratch Compensation Mode.
Fig. 4-7
8
Move the Character Blink to be compensated Scratch
Number, and set the Colour Bar Switch to the Bar side,
the Scratch Compensation Cursors will be displayed on
the Monitor as shown in Fig. 4-8.
Fig. 4-8
Note : The Cursors are not displayed when the vertical
and horizontal coordinate have been (0,0)
because of out of effective picture field.
8
Operate the cursor position by the PAGE, ITEM, UP and
DOWN Buttons of the Remote Control Box.
8
The scratch has been eliminated when coincide the
cursors intersection and scratch position.
8
Set the Colour Bar Switch of the Remote Control Box to
the Camera side.
1. V: 000L O H: 000
2. V: 000L O H: 000
3. V: 000L O H: 000
4. V: 000L O H: 000
5. V: 000L O H: 000
6. V: 000L O H: 000
7. V: 000L O H: 000
8. V: 000L O H: 000
2. V: 000L O H: 000
3. V: 000L O H: 000
4. V: 000L O H: 000
5. V: 000L O H: 000
6. V: 000L O H: 000
7. V: 000L O H: 000
8. V: 000L O H: 000
AUTO
Clear
Clear
Clear all Compensation Data
End
End of Compensation Mode
Horizontal Position
Odd/Even Line
Vertical Position
Number of Scratch
H Cursor
V Cursor
Click on the first or last page to see other AW-E600E service manuals if exist.