Read Panasonic KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN Service Manual online
126
7. Double Feed Detector L(R),
C(R), or R(R) does not work
correctly.
C(R), or R(R) does not work
correctly.
1.Execute “Double Feed” test in Sec.9.3.6 to
check the detector condition.
2. Check whether the Double Feed Detectors
L(R), C(R), and R(R) are aligned property.
3. Check the following connections and
soldering condition on each connector.
a.CN2002 (DOUBLE FEED DETECTOR R
Board) to CN2005 (RELAY (LOWER)
Board)
b.CN2001 (DOUBLE FEED DETECTOR C
Board) to CN2004 (RELAY (LOWER)
Board)
c.CN2000 (DOUBLE FEED DETECTOR L
Board) to CN2003 (RELAY (LOWER)
Board)
d.CN2007 (RELAY(LOWER) Board) to
CN1014 (CONTROL Board)
4. Check the following parts’ soldering
condition to repair it.
a. CONTROL Board
IC1010 - 117,118, and 119th pins
b. RELAY (LOWER) board
All parts.
5. Check the following signals on the RELAY
(LOWER) Board.
a. DC 12 V signal (CN1014-7th pin)
b. DC 5 V signal (CN1014-5th pin)
6. Replace faulty parts or boards.
check the detector condition.
2. Check whether the Double Feed Detectors
L(R), C(R), and R(R) are aligned property.
3. Check the following connections and
soldering condition on each connector.
a.CN2002 (DOUBLE FEED DETECTOR R
Board) to CN2005 (RELAY (LOWER)
Board)
b.CN2001 (DOUBLE FEED DETECTOR C
Board) to CN2004 (RELAY (LOWER)
Board)
c.CN2000 (DOUBLE FEED DETECTOR L
Board) to CN2003 (RELAY (LOWER)
Board)
d.CN2007 (RELAY(LOWER) Board) to
CN1014 (CONTROL Board)
4. Check the following parts’ soldering
condition to repair it.
a. CONTROL Board
IC1010 - 117,118, and 119th pins
b. RELAY (LOWER) board
All parts.
5. Check the following signals on the RELAY
(LOWER) Board.
a. DC 12 V signal (CN1014-7th pin)
b. DC 5 V signal (CN1014-5th pin)
6. Replace faulty parts or boards.
U24 (Detect document
with staples (Skew
detection))
with staples (Skew
detection))
1D
00
00
00 One of the Skew Sensors detected
document skew.
1. Refer to each item on classification code
U20.
2. Check whether the scanned documents are
stapled.
3. Set the documents neatly on the Hopper,
and then scan them again.
U20.
2. Check whether the scanned documents are
stapled.
3. Set the documents neatly on the Hopper,
and then scan them again.
U25 (Detect document
with staples (Double-
feed detection)
with staples (Double-
feed detection)
1E
00
00
xx
Double Feed Detector detected
a double-feed.
a double-feed.
1. Refer to each item on classification code
U23.
2. Check whether the scanned documents are
stapled.
3. Set the documents neatly on the Hopper,
and then scan them again.
U23.
2. Check whether the scanned documents are
stapled.
3. Set the documents neatly on the Hopper,
and then scan them again.
U26 (Bent Paper was
detected.)
detected.)
1F
xx
00
00 1. Bent Paper was detected.
1. Check whether the scanned documents are
stapled.
2. Set the documents neatly on the Hopper,
and then scan them again.
stapled.
2. Set the documents neatly on the Hopper,
and then scan them again.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN service manuals if exist.