Read Panasonic KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN Service Manual online
120
3. Starting Sensor does not work
correctly.
correctly.
1. Execute “Key/Sensor” test in Sec. 9.3.6
to check the sensor condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces its
reflector)
3. Check the following connections and
soldering condition on each connector.
a. CN3012 (STARTING SENSOR Board) to
CN2009 (RELAY(UPPER) Board)
b. CN2008 (RELAY(UPPER) Board) to
CN1015 (CONTROL Board)
4. Check the following signals.
a. STARTING signal (CN1015-19th pin)
to check the sensor condition.
2. Check the sensor alignment is proper.
(whether the sensor direction faces its
reflector)
3. Check the following connections and
soldering condition on each connector.
a. CN3012 (STARTING SENSOR Board) to
CN2009 (RELAY(UPPER) Board)
b. CN2008 (RELAY(UPPER) Board) to
CN1015 (CONTROL Board)
4. Check the following signals.
a. STARTING signal (CN1015-19th pin)
→
0 V (when none exists on the Starting
Sensor)
b. Check the reference signal for the
STARTING signal on the CONTROL signal.
b. Check the reference signal for the
STARTING signal on the CONTROL signal.
→
IC1015-6th pin: 1.5 V or less
→
IC1018-5th pin: Approx 1.5 V
c. Check comparator output signal.
→
IC1018-7th pin: 3.3 V (when no document
exists)
5. Replace faulty parts or boards.
5. Replace faulty parts or boards.
4. Mechanical problem (Drive
Roller, Drive Belt, Conveyor)
Roller, Drive Belt, Conveyor)
1. Execute “Feed Motor” and “Conveyor
Motor” tests in Sec. 9.3.6 to check the
mechanical condition.
2. Check whether the Drive Rollers (especially
Drive Roller 1), the Drive belt, and the
conveyor to support the Drive Rollers are
assembled properly in the scanner.
Motor” tests in Sec. 9.3.6 to check the
mechanical condition.
2. Check whether the Drive Rollers (especially
Drive Roller 1), the Drive belt, and the
conveyor to support the Drive Rollers are
assembled properly in the scanner.
5. Conveyor Motor does not work
properly.
properly.
1. Check the motor mechanism condition by
carrying out “Conveyor Motor” test. (See
9.3.6.)
2. Check the following connection and
soldering condition on each connector.
carrying out “Conveyor Motor” test. (See
9.3.6.)
2. Check the following connection and
soldering condition on each connector.
→
Separation Motor to CN4011(DRIVE
Board)
3. Check the following signals on the DRIVE
Board.
3. Check the following signals on the DRIVE
Board.
→
CN4011-1, 3, 4, and 6th pins:
See Fig. 7.
4. Replace faulty cables.
5. Replace the Conveyor Motor.
4. Replace faulty cables.
5. Replace the Conveyor Motor.
6. Conveyor Motor circuit does not
work properly.
work properly.
1. Check the following connections and
soldering condition on each connector.
a. CN1002 (CONTROL Board) to CN4004
(DRIVE Board)
b. CN1003 (CONTROL Board) to CN4005
(DRIVE Board)
c. CN1001 (CONTROL Board) to CN4003
(DRIVE Board)
2. Check the soldering condition of IC4005 and
its surrounding parts.
3. Check the following signals on the DRIVE
Board.
a. IC4005-11th pin (CLK): See Fig. 8.
b. IC4005-7th pin (VREF): 2.3 V or less.
c. IC4005-15th pin (ENABLE): 5 V
(when executing Conveyor Motor test)
4. Check the soldering condition of IC1028 on
the CONTROL Board to repair it.
5. Replace faulty parts or boards.
soldering condition on each connector.
a. CN1002 (CONTROL Board) to CN4004
(DRIVE Board)
b. CN1003 (CONTROL Board) to CN4005
(DRIVE Board)
c. CN1001 (CONTROL Board) to CN4003
(DRIVE Board)
2. Check the soldering condition of IC4005 and
its surrounding parts.
3. Check the following signals on the DRIVE
Board.
a. IC4005-11th pin (CLK): See Fig. 8.
b. IC4005-7th pin (VREF): 2.3 V or less.
c. IC4005-15th pin (ENABLE): 5 V
(when executing Conveyor Motor test)
4. Check the soldering condition of IC1028 on
the CONTROL Board to repair it.
5. Replace faulty parts or boards.
U13 (Conveyor Jam2:
Paper did not reach the
Paper Jam Sensor.)
Paper did not reach the
Paper Jam Sensor.)
13
00
00
00 1. Document remains between
Starting Sensor and Paper Jam
Sensor
Sensor
Remove the document from the scanner.
Error Code
Possible Cause
Check Point
Remarks
Classification
Code
ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN service manuals if exist.