Read Panasonic WJ-SX550 Service Manual Supplement online
– 47 –
8
Set the SW10-7 to On, the 7-segment LED should be
indicated A
.
7 and the Data “STX SA 112 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW10-7 to Off, the 7-segment LED should be
indicated A 7 and the Data “STX SA 113 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW10-8 to On, the 7-segment LED should be
indicated A
.
8 and the Data “STX SA 114 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW10-8 to Off, the 7-segment LED should be
indicated A 8 and the Data “STX SA 115 ETX” is trans-
mitted to the RS-232C line.
8
After completion the check of the SW10, all sections of
the SW10 are reset to the Off positions.
8
Set the SW11-1 to On, the 7-segment LED should be
indicated b
.
1 and the Data “STX SA 116 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-1 to Off, the 7-segment LED should be
indicated b 1 and the Data “STX SA 117 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-2 to On, the 7-segment LED should be
indicated b
.
2 and the Data “STX SA 118 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-2 to Off, the 7-segment LED should be
indicated b 2 and transmit the Data “STX SA 119 ETX” to
the RS-232C line.
8
Set the SW11-3 to On, the 7-segment LED should be
indicated b
.
3 and the Data “STX SA 120 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-3 to Off, the 7-segment LED should be
indicated b 3 and the Data “STX SA 121 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-4 to On, the 7-segment LED should be
indicated b
.
4 and the Data “STX SA 122 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-4 to Off, the 7-segment LED should be
indicated b 4 and the Data “STX SA 123 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-5 to On, the 7-segment LED should be
indicated b
.
5 and the Data “STX SA 124 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-5 to Off, the 7-segment LED should be
indicated b 5 and the Data “STX SA 125 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-6 to On, the 7-segment LED should be
indicated b
.
6 and the Data “STX SA 126 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-6 to Off, the 7-segment LED should be
indicated b 6 and the Data “STX SA 127 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-7 to On, the 7-segment LED should be
indicated b
.
7 and the Data “STX SA 128 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-7 to Off, the 7-segment LED should be
indicated b 7 and the Data “STX SA 129 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-8 to On, the 7-segment LED should be
indicated b
.
8 and the Data “STX SA 130 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW11-8 to Off, the 7-segment LED should be
indicated b 8 and the Data “STX SA 131 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW12-1 to On, the 7-segment LED should be
indicated C 1 and the Data “STX SA 132 ETX” is trans-
mitted to the RS-232C line.
8
Set the SW12-2 to On, the 7-segment LED should be
indicated C 2 and the Data “STX SA 133 ETX” is trans-
mitted to the RS-232C line.
8
After completion the check of the SW11, all sections of
the SW11 are reset to the Off positions.
8
Set the Mode Switch SW1 on the 7 Seg Board to 0, the 7-
segment LED should be indicated 0 0 and the Data “STX
SA 134 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 1, the 7-
segment LED should be indicated 0 1 and the Data “STX
SA 135 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 2, the 7-
segment LED should be indicated 0 2 and the Data “STX
SA 136 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 3, the 7-
segment LED should be indicated 0 3 and the Data “STX
SA 137 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 4, the 7-
segment LED should be indicated 0 4 and the Data “STX
SA 138 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 5, the 7-
segment LED should be indicated 0 5 and the Data “STX
SA 139 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 6, the 7-
segment LED should be indicated 0 6 and the Data “STX
SA 140 ETX” is transmitted to the RS-232C line.
8
Set the Mode Switch SW1 on the 7 Seg Board to 7, the 7-
segment LED should be indicated 0 7 and the Data “STX
SA 141 ETX” is transmitted to the RS-232C line.
Click on the first or last page to see other WJ-SX550 service manuals if exist.