Read Panasonic BM-ET300 / BM-ET300E Service Manual online
– 2-4 –
3. Connection and Setting Up for Adjustment
3-1 Connection
Fig. 11
3-2-1 Installing Adjustment Tool
Install the camera setting tool into a folder of the person-
al computer, and expand it.
al computer, and expand it.
IrisCmrAdjustKno.exe
3-2-2 Installing Setup Software
Install the initializing software on the personal computer.
3-3 Turn off the power. (If the iris camera is removed from
the wall, keep the rear tamper detection switch in its on
state using a tape or the like.
state using a tape or the like.
3-4 Remove the two tamperproof screws that fasten the iris
camera front panel from the bottom of the camera, then
take the front cover off. Keep the tamper detection
switch in a pressed state using a tape or the like.
take the front cover off. Keep the tamper detection
switch in a pressed state using a tape or the like.
* If power is switched on while the front cover is open,
the tamper detection switch closes and the set data
becomes erased in 30 seconds.
becomes erased in 30 seconds.
3-5 Connect the iris camera and setup PC with the exclusive
setup cable supplied to the administration software.
Attach the round connector of the cable to the setup
cable connector of the iris camera, and then attach the
D-sub 9 pin connector of the cable to the serial port of
Setup PC. (When attaching the round connector to the
iris camera, direct the cable to the left of the connector.)
Attach the round connector of the cable to the setup
cable connector of the iris camera, and then attach the
D-sub 9 pin connector of the cable to the serial port of
Setup PC. (When attaching the round connector to the
iris camera, direct the cable to the left of the connector.)
3-6 Change the positions of the DIP switches as shown in
Fig. 12 to set the iris camera out of damper detection
mode.
mode.
Fig. 12
3-7 Turn on the power of the external power-supply device.
Wait until the guide and result indicator goes out.
3-8 Start the installed BM-ET300 Setup Software to initialize
the iris camera. The BM-ET300 Login screen appears
on the monitor as shown in Fig. 13.
on the monitor as shown in Fig. 13.
Fig. 13
3-9 Select the port used for connecting the personal comput-
er and the iris camera from COM Port. Enter the pass-
word BMET300 (Default password) and press the [OK]
button. (Uppercase and lowercase characters are taken
differently.)
word BMET300 (Default password) and press the [OK]
button. (Uppercase and lowercase characters are taken
differently.)
3-10 The values set in the iris camera are read into the ini-
tializing software. The read process ends a few seconds
after its start, and the word [Completed] appears on the
monitor.
after its start, and the word [Completed] appears on the
monitor.
3-11 After the [OK] button on the monitor is pressed, the
setup software screen appears as shown in Fig. 14.
Enter the camera ID, ET300 IP Address, Server IP
Address, Gateway IP Address, and Subnetmask on the
setup software screen.
Enter the camera ID, ET300 IP Address, Server IP
Address, Gateway IP Address, and Subnetmask on the
setup software screen.
Fig. 14
3-12 Click [Store]. Or select [Connection (C)] - [Store (S)] on
the menu bar.
Click [Close] to quit the setup software.
Switch the power supply off.
Click [Close] to quit the setup software.
Switch the power supply off.
3-13 Disconnect the iris camera initializing cable from the iris
camera. Connect the iris camera LAN connector to the
personal computer with the LAN cross cable.
personal computer with the LAN cross cable.
Personal
Computer
BM-ET300
8
LAN Cross Cable
8
Exclusive Setup Cable
ON
1
2
3
4
Click on the first or last page to see other BM-ET300 / BM-ET300E service manuals if exist.