Read JBL ON TIME 200ID (serv.man2) EMC - CB Certificate online
<12014165 001>
Page 15 of 73
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
IEC60065E
ASTABEAB
14.2.2
X capacitors tested to IEC 60384-14, 2
nd
edition ... : The capacitor CX1 conductively
connected between the lines of the mains
supply is subclass X2 capacitor approved
according to IEC 60384-14+A1.
supply is subclass X2 capacitor approved
according to IEC 60384-14+A1.
P
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 ...................... :
connected to the mains: tests for X2 ...................... :
No such capacitors provided.
N/A
14.2.5 a) Capacitors with volume exceeding 1750 mm³,
where short-circuit current exceeds 0,2 A:
compliance with IEC60384-1, 4.38 category B or
better ....................................................................... :
compliance with IEC60384-1, 4.38 category B or
better ....................................................................... :
All sources of the X capacitors are tested
as category B or better according to sub-
clause 4.38 of IEC 60384-14.
as category B or better according to sub-
clause 4.38 of IEC 60384-14.
P
b)
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1,
4.38 category B or better ........................................ :
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1,
4.38 category B or better ........................................ :
Electrolytic capacitors provided with
metal can.
metal can.
P
Shielded by a barrier per Table 21 .......................... :
N/A
14.3
Inductors and windings
P
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
(as relevant) and clause 20.1.4
N/A
14.3.1
Transformers and inductors marked with
manufacturer's name and type ............................... :
manufacturer's name and type ............................... :
The transformer is marked with type and
manufacturer information (as code),
provided as label on the cores.
manufacturer information (as code),
provided as label on the cores.
P
Transformers and inductors separately approved . : Tested with appliance.
N/A
14.3.2
General
P
14.3.3
Constructional requirements (complete appended
tables or include manufacturers constructional
insulation descriptions)
tables or include manufacturers constructional
insulation descriptions)
See below.
P
14.3.3.1
Clearances and creepage distances comply with
clause 13
clause 13
(see appended table 13.3 and 13.4)
P
14.3.3.2
Transformers meet the constructional
requirements
requirements
P
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible parts
(double or reinforced insulation)
between hazardous live parts and accessible parts
(double or reinforced insulation)
Reinforced or double insulation between
primary winding/parts and secondary
winding/parts. Details see appended
table 13.3 and 13.4.
primary winding/parts and secondary
winding/parts. Details see appended
table 13.3 and 13.4.
P
Coil formers and partition walls = 0,4 mm
Partition wall of T1 with 0,5mm
thickness minimum.
P
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of
14.3.4.2 are met
protective screening only if all 7 conditions of
14.3.4.2 are met
Not a class I transformer design.
N/A
Click on the first or last page to see other ON TIME 200ID (serv.man2) service manuals if exist.