Read JBL ON STAGE (serv.man3) EMC - CB Certificate online
APPENDIX
EN 60950:2000
- Page 5 of 10 -
Order No. 23171
3.2.1 S
(ES)
Supply cords of single-phase equipment
having a rated current not exceeding 10A shall be
provided with a plug according to UNE
20315:1994
provided with a plug according to UNE
20315:1994
Supply cords of single -phase equipment having a
rated current not exceeding 2.5A shall be
provided with a plug according to UNE -EN
50075:1993
rated current not exceeding 2.5A shall be
provided with a plug according to UNE -EN
50075:1993
Class I equipment provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules,
shall be provided with a plug in accordance with
standard UNE 20315:1994
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules,
shall be provided with a plug in accordance with
standard UNE 20315:1994
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2
Class III equipment.
N
3.2.1 S
(GB)
Apparatus which is fitted with a flexible cable
or cord and is designed to be connected to a
mains socket conforming to BS 1363 by means of
that flexible cable or cord and plug, shall be fitted
with a “standard plug” in accordance with
Statutory Instrument 1768 :1994 - The Plugs and
Sockets etc. (Safety) Regulations 1994, unless
exempted by those regulations.
NOTE: “standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
mains socket conforming to BS 1363 by means of
that flexible cable or cord and plug, shall be fitted
with a “standard plug” in accordance with
Statutory Instrument 1768 :1994 - The Plugs and
Sockets etc. (Safety) Regulations 1994, unless
exempted by those regulations.
NOTE: “standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Class III equipment.
N
3.2.1 S
(IE)
Apparatus which is fitted with a flexible cable
or cord and is designed to be connected to a
mains socket conforming to I.S. 411 by means of
that flexible cable or cord and plug shall be fitted
with a 13A plug in accordance with Statutory
Instrument 525 :1997 – National Standards
Authority of Ireland (section 28) (13A Plugs and
Conversions Adaptors for Domestic Use)
Regulations 1997
mains socket conforming to I.S. 411 by means of
that flexible cable or cord and plug shall be fitted
with a 13A plug in accordance with Statutory
Instrument 525 :1997 – National Standards
Authority of Ireland (section 28) (13A Plugs and
Conversions Adaptors for Domestic Use)
Regulations 1997
Class III equipment.
N
3.2.3 C
Delete the NOTE 1 and in table 3A, delete the
conduit sizes in parentheses
conduit sizes in parentheses
Considered.
N
3.2.5 C
Replace
"60245 IEC 53" by "H05 RR-F"
"60227 IEC 52" by "H03 VV-F or H03 VVH2 -F"
"60227 IEC 53" by "H05 VV-F or H05 VVH2 -F2"
In table 3B, replace the first four lines by the
following:
Up to and including 6 0.75
"60245 IEC 53" by "H05 RR-F"
"60227 IEC 52" by "H03 VV-F or H03 VVH2 -F"
"60227 IEC 53" by "H05 VV-F or H05 VVH2 -F2"
In table 3B, replace the first four lines by the
following:
Up to and including 6 0.75
1)
Over 6 up to and including 10 (0.75)
2)
1.0
Over 10 up to and including 16 (1.0)
3)
1.5
In the Conditions applicable to table 3B, delete the
words "in some countries" in condition 1).
In NOTE 1, delete the second sentence.
words "in some countries" in condition 1).
In NOTE 1, delete the second sentence.
Considered.
N
Click on the first or last page to see other ON STAGE (serv.man3) service manuals if exist.