Read Sony KV-HG21M60 Service Manual online
– 7 –
KV-HG21M60/L,M80,M80/H,M80/L,P52/L
RM-GA002
SECTION 2
WIRE DRESSING
2-3. Mount Caution for Connector Assy, 5P (200V)
2-1. H3 Board Caution Point
2-2. UL wire P/N 1-923-082-52 dressing
on A Board
R82
R829
R889
Connector Assy,
3P P/N: 1-910-031-76
Refer to
printing:
GRAY wire to
Pin 3 (KEY)
printing:
GRAY wire to
Pin 3 (KEY)
W068
W069
UL wire
P/N 1-923-082-52
Refer to
printing:
WHITE wire
to
Pi 1 (GND)
printing:
WHITE wire
to
Pi 1 (GND)
CAUTION:
Make sure Connector Assy,
3P (P/N: 1-910-031-76) is
inserted to correct pins:
--> WHITE wire to Pin 1
--> GRAY wire to Pin 3
--> Pin 2 is NOT connected
Make sure Connector Assy,
3P (P/N: 1-910-031-76) is
inserted to correct pins:
--> WHITE wire to Pin 1
--> GRAY wire to Pin 3
--> Pin 2 is NOT connected
CAUTION:
Prevent tie, cable from
touching rear cover or any
enclosures by turning them
away from it
--> avoid rattle sound. Also
prevent tie, cable's end from
touching solder side of
board.
Prevent tie, cable from
touching rear cover or any
enclosures by turning them
away from it
--> avoid rattle sound. Also
prevent tie, cable's end from
touching solder side of
board.
CAUTION:
Prevent tie, cable from touching
rear cover or any enclosures by
turning them away from it
--> avoid rattle sound. Also
prevent tie, cable's end from
touching solder side of board.
Prevent tie, cable from touching
rear cover or any enclosures by
turning them away from it
--> avoid rattle sound. Also
prevent tie, cable's end from
touching solder side of board.
CAUTION:
Dress & control mounted wires on C boards
if necessary :
--> ensure wires do not get trapped during
solder dip process
--> ensure wires do not get punched by ICT
jig. (modify ICT jig if applicable)
Dress & control mounted wires on C boards
if necessary :
--> ensure wires do not get trapped during
solder dip process
--> ensure wires do not get punched by ICT
jig. (modify ICT jig if applicable)
Dress UL Wire (1-923-082-52) according to Figure 1(b) as
shown
Note : Ensure UL wire does not touch high temperature
resistors R828, R829 & R889
shown
Note : Ensure UL wire does not touch high temperature
resistors R828, R829 & R889
Ensure UL wire does not touch high
temperature resistors R828, R829 & R889
temperature resistors R828, R829 & R889
C/M for picture bending
due to introduction of
Sparkling Wega 2 Features
(DCN : S0062)
due to introduction of
Sparkling Wega 2 Features
(DCN : S0062)
CAUTION:
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
1. Do not overpull the wire during dressing
_> avoid disconnection of wires.
2. Make sure wires are kept away from
sharp edges, heatsinks & other
hight-temperature parts.
Legend:
Hook
Click on the first or last page to see other KV-HG21M60 service manuals if exist.