KV-32FQ85B - Sony TV Service Manual (repair manual). Page 10

Teletext is an information service transmitted by most TV stations. The index page of the teletext service 
(usually page 100) gives you information on how to use the service. To operate teletext, use the remote control 
buttons as indicated below.

Teletext errors may occur if you use a channel (TV Broadcast) with a weak signal.

Select the broadcast channel which carries the teletext 
service you wish to view.

Press the  

 button one time to enter Picture and 

Text (P&T) mode. The screen is divided into two with 
the Text display on the left and the TV channel in the 
right corner.

If you wish to view the Text in full screen mode, press 
the 

 button a second time.

Input 3 digits for the page number, using the numbered buttons.

  If you make a mistake, re type the correct page number.
  If the counter on the screen continues searching, it is because the page 

is not available. If this is the case, input another page number.

To access the next or preceding page:
Press PROG +  (

) or PROG - (

).

To freeze a teletext page:
Press 

/

. Press it again to cancel the freeze. 

To reveal concealed information (e.g: answer to a quiz):
Press 

/

. Press it again to conceal the information. 

A teletext page may consist of several sub pages. In this case, one or more arrows appear  next 
to the page number and an information box is displayed at the bottom of the screen showing the 
number of sub pages contained on this page. As soon as sub pages are available, they start to 
automatically  run. If you want to stop the show and select your desired sub page, press 
repeatedly

 

B

 or 

b

. 

To Switch Off Teletext: 
Press .

Fastext service lets you access Teletext pages with one button push.
When you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at  

the bottom of the teletext page. Press the appropriate coloured button (red, green, yellow  
or blue) to access the page corresponding to your menu choice.

 Press 

 to display PAP. 

 

One of the screens will be framed to indicate that this is 

the active screen. It means that when you want to select 
the PAP source, you will be doing it in the active screen.

 Press 

 again to remove PAP.

On the screen appears a banner guiding you how to operate 
PAP. This banner will disappear after some seconds but it 
always can be displayed again by pressing the 

 button.

This is only possible if Media Selector is set to TV.

To change the active screen (framed), press the

 

B

 or 

b

 buttons. 

 

Selecting a TV channel:
Press the

 

B

 button to select the left screen as the active screen. Next press the number buttons 

or 

PROG +/- to select a TV channel.

 Video input signals can not be displayed on the left screen.

  Selecting an input source:

Press the

 

b

 button to select the right screen as the active screen. Next press repeatedly the 

 

button to watch the input signal of a connected equipment onto the TV right screen. For more 
details on which input symbol you want to choose, please see section "Viewing pictures from 
equipment connected to the TV" on page 27.

    

RF signal (TV broadcast channels) can not be displayed on the right screen.

Selecting the sound
The sound of the active screen (framed) always comes from the TV set loudspeakers.
Besides that, you can listen to the active screen as well as the non active screen via headphones.

To do this:
With the PAP switched on, refer to the section "The Sound Adjustment Menu", select "Headphones 
Set Up" and set the option "

 PAP Sound" according your preference. For details see page 13.

Navegador

Configuración del Sistema

Aceptar

Versión

PROG+ PROG-

Select:

Select:

Move Frame

03

PAP divides the screen into two to watch two pictures in format 4:3 simultaneously.