Read Sony KV-32FQ85B Service Manual online
- 6 -
e
g
a
s
s
e
M
r
o
r
r
E
D
E
L
e
d
o
C
r
o
r
r
e
o
N
0
0
d
e
v
r
e
s
e
R
1
0
)
n
o
i
t
c
e
t
o
r
P
t
n
e
r
r
u
C
r
e
v
O
(
P
C
O
2
0
n
o
i
t
c
e
t
o
r
P
e
g
a
t
l
o
V
r
e
v
O
3
0
c
n
y
S
l
a
c
i
t
r
e
V
o
N
4
0
n
o
r
e
w
o
p
t
a
r
o
r
r
E
R
K
I
5
0
n
o
r
e
w
o
p
t
a
w
o
l
s
e
n
il
a
t
a
d
r
o
/
d
n
a
k
c
o
l
c
s
u
b
C
I
I
6
0
n
o
r
e
w
o
p
t
a
e
g
d
e
l
w
o
n
k
c
a
s
u
b
C
I
I
o
n
M
V
N
7
0
n
o
i
t
c
e
t
o
r
P
l
a
t
n
o
z
i
r
o
H
8
0
n
o
r
e
w
o
p
t
a
e
g
d
e
l
w
o
n
k
c
a
o
n
r
e
n
u
T
9
0
r
o
r
r
E
r
o
s
s
e
c
o
r
P
d
n
u
o
S
0
1
d
e
v
r
e
s
e
R
1
1
r
o
r
r
E
e
t
a
r
n
a
c
S
2
1
r
o
r
r
E
C
A
D
3
1
r
o
r
r
E
d
n
e
k
c
a
B
4
1
r
o
r
r
E
e
c
n
e
g
r
e
v
n
o
C
c
i
m
a
n
y
D
5
1
r
o
r
r
E
P
I
P
6
1
AE-6BAD/Y SELF DIAGNOSTIC SOFTWARE
The identification of errors within the AE-6BAD/Y chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In
the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted) See table 1, non fatal errors are reported using this
method. Each time the software detects an error it is stored within the NVM. See Table 2.
the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant
device number will be displayed through the LED (Series of flashes which must be counted) See table 1, non fatal errors are reported using this
method. Each time the software detects an error it is stored within the NVM. See Table 2.
Table 1
How to enter into Table 2
1.
Turn on the main power switch of the TV set.
2.
Program Remote Commander for Operation in Service
Mode. [See Page 21].
Mode. [See Page 21].
3.
Press ‘AUX/VIDEO’ ‘AUX/VIDEO’ > ‘MENU’ on the
Remote Commander.
Remote Commander.
4.
Using the Remote Commander, Scroll to the ‘Error’ item
using the down arrow key, then press the right arrow
key.
using the down arrow key, then press the right arrow
key.
5.
The following table will be displayed indicating the error
count.
count.
Table 2
Note: To clear the error count data press ‘80’ on the Remote
commander.
commander.
Flash Timing Example : e.g. error number 3
StBy LED
ON
ON
ON
OFF
OFF
r
o
t
i
n
o
m
r
o
r
r
E
)
s
e
t
u
n
i
M
:
s
r
u
o
H
(
:
E
M
I
T
G
N
I
K
R
O
W
3
3
:
2
8
:
s
r
e
t
n
u
o
c
r
o
r
r
E
P
C
O
:
2
0
E
0
P
V
O
:
3
0
E
0
C
N
Y
S
V
O
N
:
4
0
E
0
R
K
I
:
5
0
E
0
C
I
I
:
6
0
E
0
M
V
N
:
7
0
E
0
T
O
R
P
H
:
8
0
E
0
R
E
N
U
T
:
9
0
E
0
D
N
U
O
S
:
0
1
E
0
S
T
L
O
V
9
:
1
1
E
0
E
T
A
R
N
A
C
S
:
2
1
E
0
B
M
O
C
D
3
:
3
1
E
0
D
N
E
K
C
A
B
:
4
1
E
0
N
O
C
N
Y
D
:
5
1
E
0
E
G
A
T
L
O
V
H
G
I
H
:
6
1
E
0
H
C
T
I
W
S
V
A
:
7
1
E
0
C
E
D
A
M
O
R
H
C
:
8
1
E
0
A
C
R
F
:
9
1
E
0
G
N
E
J
P
:
0
2
E
0
C
A
D
:
1
2
E
0
T
O
R
P
R
E
K
A
E
P
S
:
4
2
E
0
K
C
I
T
S
Y
R
O
M
E
M
:
5
2
E
0
:
t
c
e
l
e
S
:
u
n
e
M
s
u
o
i
v
e
r
P
Click on the first or last page to see other KV-32FQ85B service manuals if exist.