Read Sony KDS-50A3000 / KDS-55A3000 / KDS-60A3000 Service Manual online
KDS-50A3000/55A3000/60A3000
KDS-50A3000/55A3000/60A3000
14
1-7. CHASSIS
REMOVAL
2
1
FB1A Block Assembly
AC Bracket
(F Board Bracket)
(F Board Bracket)
Chassis Block
1 Remove 2 screws from the Rear Cabinet and the
AC Bracket, +BVTP 3x12 TYPE2 IT-3
2 Remove 2 screws from the FB1A Block Assembly,
+BVTP2 4x16
7
8
9
13
14
6
4
3
5
10
11
12
Fan Bracket
G Board
A Board
D.C. Fan (60x60)
Turn Rivet
Terminal Bracket
U Board
G Bracket
AU Shield
BC Board
BC Shield
FB1 Block
TUU2 Block
F Board
3 G Board – Disconnect 6 connectors then remove 6 screws, +BVTP 3x12 TYPE2 IT-3
4 Fan Bracket – Disconnect 1 Connector then remove 2 screws, +BVTP2 4x16
5 Turn Rivet – Unscrew and carefully pull out from the fan to release it from the shield.
4 Fan Bracket – Disconnect 1 Connector then remove 2 screws, +BVTP2 4x16
5 Turn Rivet – Unscrew and carefully pull out from the fan to release it from the shield.
Note: The fan is secured to the Chassis Assembly with Turn Rivet screws. To remove these screws use a screw driver to unscrew the
screw until it lifts slightly above the rivet then pull the screw and the rivet out from the fan.
screw until it lifts slightly above the rivet then pull the screw and the rivet out from the fan.
6 A Board – Disconnect 2 connectors then remove 3 screws, +BVST3x6, and pull out from the FB1A Block Assembly connector
7 F Board – Disconnect 2 connectors then remove 2 screws, +BVST 3x6
8 TUU2 Block – Release the RF connector
9 FB1A Block Assembly – Disconnect 6 connectors
7 F Board – Disconnect 2 connectors then remove 2 screws, +BVST 3x6
8 TUU2 Block – Release the RF connector
9 FB1A Block Assembly – Disconnect 6 connectors
10 BC Board – Disconnect 2 connectors then remove 2 screws, +BVST 3x6
11 BC Shield – Remove 3 screws, +BVST 3x6
12 G Bracket – Remove 6 screws, +BVST 3x6, then remove the AU Shield by removing 1 screw, +BVST 3x6
13 U Board – Disconnect 1 connector, remove 2 screws +BVST 3x6, and pull out from FB1A Block Assembly connector
14 Terminal Bracket - Remove 3 screws, +PSW M3x8, 5 screws, + BVTP 3x12 TYPE2 IT-3, and 1 Hex Nut and 1 Washer
13 U Board – Disconnect 1 connector, remove 2 screws +BVST 3x6, and pull out from FB1A Block Assembly connector
14 Terminal Bracket - Remove 3 screws, +PSW M3x8, 5 screws, + BVTP 3x12 TYPE2 IT-3, and 1 Hex Nut and 1 Washer
Caution: When replacing any part of the chassis be sure to remove any dust particles and clean the mirror.
Click on the first or last page to see other KDS-50A3000 / KDS-55A3000 / KDS-60A3000 service manuals if exist.