HDR-CX530E, HDR-CX535, HDR-CX610E, HDR-PJ530E, HDR-PJ540, HDR-PJ540E, HDR-PJ610E (serv.man2) - Sony Movie Service Manual (repair manual). Page 7

1-3

HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2

C6814 C6815

C6816 C6817

R1401

IC6800

approx. 330 msec

Note: The length of low section will vary a little depending on the conditions.

Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

6

1

1

1

The abnormalities in initialization of 
the focus lens and the abnormalities in 
initialization of the zoom lens occurred 
simultaneously.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

E

6

1

3

0

Reset position detection error on the 
stepper iris initializing

Turn the power on to open lens barrier. Disconnect the battery or power 
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive 
block (pin wl, ek of CN4001 on the VC-1025 board).
If iris blades work normally, confirm that they are closing completely 
and confirm following item.
•  Case of the iris blades do not close normally. Replace the lens block.
•  Case of “E: 61: 30” is appeared and iris blades closed completely.

Confirm that communication with lens block is normal.

•  Case of LCD is not displayed normally. Check that connection between 

CN6702 on CM-1004 board and CN4004 on VC-1025 board by FP-
2189 flexible board.

•  Case of LCD is displayed normally. Replace the lens block.

E

6

2

0

0

Handshake correction function does not 
work well. (With PITCH angular veloc-
ity sensor output stopped.)

Inspect PITCH angular velocity sensors (SE7701 on the JK-1009 
board) peripheral circuits.

E

6

2

0

1

Handshake correction function does not 
work well. (With YAW angular velocity 
sensor output stopped.)

Inspect YAW angular velocity sensors (SE7701 on the JK-1009 board) 
peripheral circuits.

E

6

2

0

2

Abnormality of IC for steadyshot.

Refer to “1-6-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred”.

E

6

2

0

3

IC for steadyshot and micro controller 
communication abnormality among.

Inspect the steadyshot circuit (IC7711 on the VC-1025 board).

E

6

2

0

4

Image vibration correction during hand-
shake function does not work.

Inspect the image vibration angular velocity sensors (SE7711 on the 
VC-1025 board) peripheral circuits.

E

6

2

1

0

Shift lens initializing failure.

Replacement of lens block (Note 3).
If an error occurs again, replace the VC-1025 board.

E

6

2

1

1

Shift lens overheating (Pitch)

Refer to “1-6-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred”.

E

6

2

1

2

Shift lens overheating (Yaw)

Refer to “1-6-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred”.

E

6

2

2

0

Abnormality of thermistor.

Refer to “1-6-4. E : 62 : 20 (Abnormality of Thermistor) Occurred”.

E

6

2

3

0

Abnormal CPU

Turn power off and turn power on again.

E

9

1

0

1

Abnormality when flash is being 
charged.

Turn power off and turn power on again.

E

9

1

0

2

Abnormality of LED Video light.

Turn power off and turn power on again.

E

9

1

0

3

Abnormality of LED Video light Tem-
perature detection.

Turn power off and turn power on again.

E

9

2

0

1

Battery current value goes over the max 
discharge current

Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the 
symptom is occurred after replacing the battery. If the symptom is still 
occurred, overhaul inspection is needed. Check each output of DC/
DC converter (IC5100 on the VC-1025 board) with connected the DC 
JACK (CN4007) on the VC-1025 board.
(The minimum connection to periphery)

E

9

4

0

0

Fault of writing or erasing the flash 
memory

CX535/PJ530E/PJ540/PJ540E:
Inspect the flash memory (IC8101 on the MM-102 board).
CX610E/PJ610E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

9

4

0

1

Internal flash memory fault

CX535/PJ530E/PJ540/PJ540E:
Inspect the flash memory (IC8101 on the MM-102 board).
CX610E/PJ610E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).

E

9

4

0

2

BGM data error

Check the CPU (IC6000 on the VC-1025 board).

E

9

5

0

0

GPS hardware error

Turn power off and turn power on again.

E

9

6

0

0

Map area mount error

Turn power off and turn power on again.

E

9

7

0

0

Projector hardware error

Turn power off and turn power on again.

*
*