HDR-CX530E, HDR-CX535, HDR-CX610E, HDR-PJ530E, HDR-PJ540, HDR-PJ540E, HDR-PJ610E (serv.man2) - Sony Movie Service Manual (repair manual). Page 6

1-2

HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2

4.  Confirm on the personal computer that the unit is detected as a connectable wireless network.
5.  To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection”from the icon 

displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7701 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.

Note: The sensor sensitivity of SE7701 (PITCH/YAW) on JK-1009 board is written only repair parts.

P: PITCH sensor sensitivity

Y: YAW sensor sensitivity

Type A:

Type B:

P Y

P Y

SE7701

When problems occur while the unit is operating, the self-diagnosis 
function starts working, and displays on the Viewfinder or the LCD 
screen what to do.
This function consists of two display; self-diagnosis display and service 
mode display. Details of the self-diagnosis functions are provided in the 
Instruction manual.

When problems occur while the unit is operating, the counter of the 
Viewfinder or the LCD screen shows a 4-digit display consisting of an 
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display 
indicates the “repaired by:”, “block” in which the problem occurred, and 
“detailed code”of the problem.

0 0

3 2

C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Tabl e”.

Indicates the appropriate

step to be taken.

E.g.
13 ....
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer

E : Corrected by service

engineer

Format the “memory card”.

Viewfinder or LCD screen

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

0

4

0

0

Non-standard battery is used.

Use the InfoLITHIUM battery.

C

0

6

0

0

The battery pack temperature is high.

Change the battery pack or place it in a cool place.

C

1

3

0

1

Memory card is unformatted. 
Memory card is broken.

Format the memory card. 
Insert a new memory card.

C

1

3

0

2

Access error

Remove the power source. Reconnect it again and operate your cam-
corder again.

C

1

3

0

3

Access error (External media)

Turn power off and turn power on again.

C

1

3

0

4

Drive fault (External media)

Turn power off and turn power on again.

C

E

3

2

6

1

6

0

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, 
check the focus drive signal of lens block (pin wg of CN4001 on the 
VC-1025 board). If it is OK, check the focus motor drive IC (IC6800 
on the VC-1025 board).

E

2

0

0

0

Flash memory data are rewritten.

Make flash memory data correct value. (Note 1)

E

3

1

0

0

Drive fault

Turn power off and turn power on again.

E

4

1

0

0

Wi-Fi Module Hardware Error

Check that connection between CN4902 on the VC-1025 board and 
CN2301 on the WF-1004 board by FP-2200 flexible board.

E

6

1

1

0

Zoom operations fault
(Cannot initialize zoom lens.)

Inspect the lens block zoom drive signal (pin rd of CN4001 on the VC-
1025 board when zooming is performed when the zoom lever is oper-
ated, and the zoom motor drive circuit (IC6800 on the VC-1025 board) 
when zooming is not performed.

*

*
*

(

)

*

Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.

The changed portions from
Ver. 1.0 are shown in blue.