Read Sony HDR-CX530E / HDR-CX535 / HDR-CX610E / HDR-PJ530E / HDR-PJ540 / HDR-PJ540E / HDR-PJ610E (serv.man2) Service Manual online
1-8
HDR-CX530E/CX535/CX610E/PJ530E/PJ540/PJ540E/PJ610E_L2
– ENGLISH –
(5) Set the Plate of the Motor A in the state shown in the figure and
install the Motor A matching it with the two bosses on the Sheet
Metal A, and then tighten three screws in the order shown in the
figure below.
Metal A, and then tighten three screws in the order shown in the
figure below.
Screw
(A)
Tightening torque = 0.12 ± 0.02N · m (1.2 ± 0.2kg f · cm)
Screw
(B)
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
FRO
NT
TOP
Screws
(A)
(A)
Sheet Metal A
Screws
(B)
(B)
Motor A
Boss
Boss
Screw
(B)
(B)
1
2
3
(6) Attach the Edge of Mechanical Rubber to the Sheet Metal B and
install the Sheet Metal B while matching it with the two bosses.
Tighten three screws in the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Screws
Sheet Metal B
Boss
Boss
Mecha Stop Rubber
FRONT
TO
P
1
2
3
(7) Stick the Adhesive Part of the Motor A Flexible Board while
matching it with the two bosses.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
Adhesive part
Adhesive part
Flexible Board of
the Motor A
the Motor A
Flexible Board of
the Motor A
the Motor A
Bosses
Shape and sticking position
of Adhesive Sheet
of Adhesive Sheet
FRONT
TOP
(8) Install the Frame (E-SUB-A), Frame (E-SUB-B), and Ball Bear-
ing while matching the six bosses and the shaft with the holes, and
then tighten six screws in the order shown in the figure below.
then tighten six screws in the order shown in the figure below.
Screws
Screws
Bosses
Bosses
Shaft
Hole
Frame (E-SUB-A),
Ball Bearing
Ball Bearing
Frame (E-SUB-B)
FRONT
TOP
2
1
4
3
5
6
(9) Stick the Adhesive Part of the FP-2189 Flexible Board and the
Radiation Sheet while attaching the four bosses and connecting
the connector.
the connector.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
Shape and sticking position
of Adhesive Sheet
of Adhesive Sheet
Adhesive
part
part
FP-2189 Flexible Board
Bosses
Adhesive
part
part
Adhesive
part
part
Bosses
FP-2189
Flexible Board
Flexible Board
FP-2189 Flexible Board
Connector
Connector
CM Radiation Sheet
FR
ONT
TOP
TOP
(10) Set the Plate of the Motor B to the state shown in the figure and
attach the two bosses of the Motor B while matching them with
the holes in the Sheet Metal B, and then tighten three screws in
the order shown in the figure below.
the holes in the Sheet Metal B, and then tighten three screws in
the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Bosses
Screws
Motor B
FR
ONT
TO
P
1
2
3
(11) Install the Frame (F-SUB-A), Frame (F-SUB-B), and Ball Bear-
ing while attaching the four bosses and the shaft, and then tighten
five screws in the order shown in the figure below.
five screws in the order shown in the figure below.
Tightening torque = 0.18 ± 0.02N · m (1.8 ± 0.2kg f · cm)
Screws
Boss
Boss
Boss
Bosses
Shaft
Motor B
Frame (F-SUB-B),
Ball Bearing
Ball Bearing
Frame (F-SUB-A)
Screws
TOP
FRONT
1
2
3
5
4
Click on the first or last page to see other HDR-CX530E / HDR-CX535 / HDR-CX610E / HDR-PJ530E / HDR-PJ540 / HDR-PJ540E / HDR-PJ610E (serv.man2) service manuals if exist.