Read Sony HDR-CX500 / HDR-CX500E / HDR-CX500V / HDR-CX500VE / HDR-CX505VE / HDR-CX520 / HDR-CX520E / HDR-CX520V / HDR-CX520VE (serv.man2) Service Manual online
1-6
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
CX520/CX520E/CX520V/CX520VE_L2
1-4-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
7430
01
Write the data. (After it starts, set it before caution is displayed.)
2
11
8E
F656
01
Write the data.
3
11
8E
F657
F0
Write the data.
4
11
8E
F659
01
Write the data. (Note 1)
5
11
8E
F659
00
Write the data.
6
11
8E
F656
00
Write the data.
7
11
8E
F657
10
Write the data.
8
11
8E
F659
01
Write the data. (Note 1)
9
11
8E
F659
00
Write the data.
10
11
80
7430
00
Write the data.
11
Check if the shift lens moves while setting the order 2 to 9. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 12.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 12.
12
While setting the order 2 to 9, measure with an oscilloscope the output voltage of R5524 in the
periphery of IC5501 on the VC-575 board to check the output voltage varies.
periphery of IC5501 on the VC-575 board to check the output voltage varies.
13
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 14.
varied, proceed to the order 14.
14
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5653 land in the periphery of
15
IC5501 on the VC-575 board, turn the power ON to check that the output voltage immediately
after the power on change as shown in Fig. 2.
after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
16
change as shown in Fig. 2, inspect the camera control circuit (IC7501 of VC-575 board)
periphery.
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F659, data: 00, and then retry.
Note 2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-4-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens block and VC-575 board.
3
In case of no malfunction of connections, replace the lens block with new one. (Note) When the error has occurred in spite of the
lens replacement, replace VC-575 board with new one.
lens replacement, replace VC-575 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
Click on the first or last page to see other HDR-CX500 / HDR-CX500E / HDR-CX500V / HDR-CX500VE / HDR-CX505VE / HDR-CX520 / HDR-CX520E / HDR-CX520V / HDR-CX520VE (serv.man2) service manuals if exist.