Read Sony DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man4) Service Manual online
6-12
DCR-SR30E/SR40/SR40E_ADJ
2.
Modification of E, F, 19, 1E, 1F Page Data
If the E, F, 19, 1E, 1F page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages E, F, set data: 00 to page: 0,
address: 10, and then select pages E, F.
3) If modification of data on pages 19, 1E, 1F, set data: 01 to
page: 0, address: 10, and then select pages 9, E, F.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note 1:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
6) Check that the data at the addresses for adjustment are initial
values (adjustment initial values) listed in the table.
If different, change them to the adjustment initial values.
If different, change them to the adjustment initial values.
Processing after Completing Modification E, F, 19, 1E, 1F
page data:
page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE (Write) button.
Note 2:
This operation should be done with the adjustment re-
mote commander. The operation of page: 02 cannot be
performed with the SeusCam.
mote commander. The operation of page: 02 cannot be
performed with the SeusCam.
1-2-2.
Initialization of E, F, 19, 1E, 1F Page Data
1.
Initializing of E, F, 19, 1E, 1F Page Data
Note 1:
If “Initialization of Pages E, F, 19, 1E, 1F” is executed,
all data on pages E, F, 19, 1E, 1F are initialized. (Only an
individual page cannot be initialized)
all data on pages E, F, 19, 1E, 1F are initialized. (Only an
individual page cannot be initialized)
Note 2:
If the E, F, 19, 1E, 1F page data has been initialized, the
following adjustments need to be performed again.
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment
following adjustments need to be performed again.
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment
Adjustment Page
E
Adjustment Address
00 to FF
Adjustment Page
F
Adjustment Address
10 to FF
Adjustment Page
19
Adjustment Address
00 to 33
Adjustment Page
1E
Adjustment Address
00 to FF
Adjustment Page
1F
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data Procedure
1
0
01
01
2
0
10
00
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
3
6
01
2D: NTSC model
2F: PAL model
2F: PAL model
4
6
03
FF
Press PAUSE (Write) button.
5
Wait for 6 seconds.
6
6
02
Check the data changes to
“01”.
“01”.
7
Perform “Modification of E,
F, 19, 1E, 1F Page Data”
F, 19, 1E, 1F Page Data”
Note 3:
NTSC model: DCR-SR40
PAL model: DCR-SR30E/SR40E
PAL model: DCR-SR30E/SR40E
Click on the first or last page to see other DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man4) service manuals if exist.