DCR-PC6E, DCR-PC9E - Sony Movie Service Manual (repair manual). Page 68

— 68 —

You can specify the recorded still image to print
out by putting marks. This function is useful for
printing out still images later.
Your camcorder conforms with the DPOF
(Digital Print Order Format) standard for
specifying the still images to print out.

Before operation
Insert a “Memory Stick” into your camcorder.

(1) Set the POWER switch to MEMORY. Make

sure that the LOCK is set to the right (unlock)
position.

(2) Press INDEX on your camcorder to display

the index.

(3) Press 

 MARK. The screen to write a print

mark appears.

(4) Press the image you want to write a print

mark. The 

 appears on the selected image.

Press EXIT.

Press the image you want to cancel the print
mark in step 4 again . The 

 disappears.

INDEX

1

2

3

4

5

6

EXIT

MARK

1

2

3

4

5

6

EXIT

DEL

MARK

-

MARK

MARK

1 / 40

T

t

2 / 40

T

t

RET

POWER

MEMORY

VCR

CAMERA

OFF

(CHARGE)  

LOCK

LOCK

Вы можете указать записанные неподвижные
изображения для распечатки, помечая их
знаками. Эта функция является полезной
для распечатки неподвижных изображений
позже.
Ваша видеокамера удовлетворяет стандарту
DPOF (цифровому формату
последовательной распечатки) для указания
неподвижных изображений для распечатки.

Перед началом работы
Вставьте “Memory Stick” в Вашу видеокамеру.

(1) Установите переключатель POWER в

положение MEMORY. Убедитесь, что
фиксатор LOCK установлен в правое
(незафиксированное) положение.

(2) Нажмите кнопку INDEX на Вашей

видеокамере для отображения индексного
экрана.

(3) Нажмите кнопку 

 MARK. Появится

экран для записи печатного знака.

(4) Нажмите изображение, на котором Вы

хотите записать печатный знак. Знак 
появится на выбранном изображении.

Нажмите кнопку EXIT.

В пункте 4 нажмите изображение, для
которого Вы хотите отменить печатный знак
еще раз. Индикация 

 исчезнет.

If the write-protect tab on the “Memory Stick”
is set to LOCK
You cannot write print marks on still images.

Moving pictures
You cannot write print marks on moving
pictures.

Если лепесток защиты записи на “Memory
Stick” установлен в положение LOCK
Вы не сможете записать печатные знаки на
неподвижных изображениях.

Движущиеся изображения
Вы не можете записать знаки печати на
движущиеся изображения.

If you run into any problem using your camcorder, use the following table to troubleshoot the
problem. If the problem persists, disconnect the power source and contact your Sony dealer. If
“C:ss:ss” appears on the screen, the self-diagnosis display function has worked. See page 213.

• The POWER switch is not set to CAMERA.

c Set it to CAMERA (p. 30).

• The tape has run out.

c Rewind the tape or insert a new one (p. 27, 50).

• The write-protect tab is set to expose the red mark.

c Use a new tape or slide the tab (p. 27).

• The tape is stuck to the drum (moisture condensation).

c Remove the cassette and leave your camcorder for at least  1

hour to acclimatize (p. 234).

• While being operated in CAMERA mode, your camcorder has

been in the standby mode for more than 5 minutes.

c Set the POWER switch to OFF (CHARGE) and then to

CAMERA (p. 30).

• The battery pack is dead or nearly dead.

c Install a fully charged battery pack.

• Viewfinder is not extended to the end.

c Pull out the viewfinder.

• The viewfinder lens is not adjusted.

c Adjust the viewfinder lens (p. 36).

• STEADYSHOT is set to OFF in the menu settings.

c Set it to ON (p. 134).

• The setting is the manual focus mode.

c Press FOCUS to set to the auto focus mode (p. 76).

• Shooting conditions are not suitable for autofocus.

c Adjust to focus manually (p. 76).

• The LCD panel is open.

c Close the LCD panel (p. 33).

• The contrast between the subject and background is too high.

This is not a malfunction.

• This is not a malfunction.

• Slow shutter, low lux or Super NightShot mode is activated.

This is not a malfunction.

START/STOP does not operate.

The power goes off.

The image on the viewfinder screen
is not clear.

The picture does not appear in the
viewfinder.

The autofocusing function does not
work.

The SteadyShot function does not
work.

A vertical band appears when you
shoot a very bright subject.

Some tiny white spots appear on the
screen.

A vertical band appears when you
shoot a subject such as lights or a
candle flame against a dark
background.

• If 10 minutes elapse after you set the POWER switch to

CAMERA or DEMO MODE is set to ON in the menu settings
without a cassette inserted, your camcorder automatically
starts the demonstration.

c Insert a cassette or press the LCD screen. The demonstration

stops. You can also cancel DEMO MODE (p. 139).

• NIGHTSHOT is set to ON.

c Set it to OFF (p. 41).

• NIGHTSHOT is set to ON in a bright place.

c Set it to OFF (p. 41).

• The backlight function is active.

c Set it off (p. 40).

• BEEP is set to OFF in the menu settings.

c Set it to MELODY or NORMAL (p. 134).

• Set STEADYSHOT to OFF in the menu settings (p. 134).

• The power of the external flash is off or the power source is not

installed.

c Turn on the external flash or install the power source.

• Two or more external flashes (optional) are attached.

c Only one external flash (optional) can be attached not fully

charged.

Picture appears too bright, and the
subject does not appear on the
screen.

The picture is recorded in incorrect or
unnatural colours.

The click of the shutter does not
sound.

A horizontal band appears when
shooting a TV screen or computer
screen.

An unknown picture is displayed on
the screen.

An external flash (optional) does not
work.