Read Sony DSC-W320 (serv.man2) Service Manual online
DSC-W320_L2
1-2
– ENGLISH –
0 0
3 2
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
13 ....
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
LCD screen
Format the “memory card”.
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
1
3
0
1
The internal memory has experienced a
media error.
media error.
Turn the power off and on again.
The internal memory has experienced a
format error.
format error.
Format the internal memory.
“memory card” is unformatted.
Format the “memory card”
“memory card” is broken.
Replace a new “memory card”.
“memory card” type error
Insert a supported “memory card”.
The camera cannot read or write data on
the “memory card”.
the “memory card”.
Turn the power off and on again, or taking out and inserting
the “memory card” several times.
the “memory card” several times.
C
3
2
0
1
Trouble with hardware
Turn the power off and on again.
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does
not recover, check the focus reset sensor of lens block
(pin qh of CN401 on the SY-244 board). If it is OK, check the
focus motor drive IC (
not recover, check the focus reset sensor of lens block
(pin qh of CN401 on the SY-244 board). If it is OK, check the
focus motor drive IC (
IC401
on the SY-244 board).
E
9
1
0
1
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement of flash unit. (Note)
Note: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
Even if you execute this function, the images are retained.
Even if you execute this function, the images are retained.
1
MENU
t
(Settings)
t
(Main Settings)
t
[Initialize]
t
[OK]
t
z
on the control button
• Be sure not to turn off the camera while initializing.
Note
1-4. POWER SUPPLY ON REPAIRING
Use the battery (NP-BN1) on repairing.
The external battery source cannot be used on repairing.
The external battery source cannot be used on repairing.
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruc-
tion manual.
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruc-
tion manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers,
whichblinks at 3.2 Hz. This 5-character display indicates the “re-
paired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
shows a 4-digit display consisting of an alphabet and numbers,
whichblinks at 3.2 Hz. This 5-character display indicates the “re-
paired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.01
Click on the first or last page to see other DSC-W320 (serv.man2) service manuals if exist.