DSC-W320 (serv.man2) - Sony Digital Camera Service Manual (repair manual)

dsc-w320 (serv.man2) service manual
Model
DSC-W320 (serv.man2)
Pages
32
Size
6.59 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-w320-sm2.pdf
Date

Read Sony DSC-W320 (serv.man2) Service Manual online

DSC-W320_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
985274436.pdf
2010H08-1
  © 2010.08
Published by Sony Techno Create Corporation
Ver. 1.5  2010.08
DIGITAL STILL CAMERA
The components identified by 
mark 
0 or dotted line with mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques pour 
la sécurité.
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Japanese Model
Tourist Model
1-1.  PRECAUTION ON REPLACING THE SY-244 BOARD
1-2.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-3.  HOW TO WRITE DATA TO INTERNAL MEMORY
1-4.  POWER SUPPLY ON REPAIRING
1-5. SELF-DIAGNOSIS FUNCTION
1-6.  PROCESS AFTER FIXING FLASH ERROR
1-7.  ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-8.  OPTICAL STEPING MOTOR (F1380) REPLACING METHOD
1-9.  DC MOTOR WORM A ASSY REPLACING METHOD
1-10. CAM TUBE BLOCK ASSY AND STRAIGHT TUBE LUBRICATED ASSY AND
 
1 GROUP FRAME REPLACING METHOD
1-11. FINAL  INSPECTION
Photo: Silver
9-852-744-36
DSC-W320
Replace the previously issued
SERVICE MANUAL 9-852-744-35
with this Manual.
Internal memory
ON BOARD
Internal memory
ON BOARD
Revised-4
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2010.01
Official Release
1.1
2010.01
Revised-1
(A1 09-392)
•  Correction of SERVICE NOTE
 Page 
1-2
1-4
•  Correction of EXPLODED VIEWS
 Page 
2-3
2-4
2-5
•  Correction of SUPPLIED ACCESSORIES
 Page 
2-7
•  Correction of FRAME SCHEMATIC DIAGRAMS
 Page 
5-1
•  Correction of PRINTED WIRING BOARDS
 Page 
6-5
6-6
Yes
1.2
2010.02
Revised-2
(A2 09-467)
•  Correction of SERVICE NOTE
 Page 
1-4
Yes
1.3
2010.03
Revised-3
(A3 09-531)
•  Revision of SUPPLIED ACCESSORIES
 Page 
2-7
Yes
1.4
2010.06
Supplement-1
(S1 10-040)
•  Addition of EXPLODED VIEWS
Yes*
1.5
2010.08
Revised-4
(A4 10-113)
•  Correction of SERVICE NOTE
 Page 
1-6
1-7
1-9
Yes
*: S.M. revised only top cover.
DSC-W320_L2
– 2 –
SPECIFICATIONS
概略仕様
– ENGLISH –
– JAPANESE –
Camera
[System]
Image device: 7.76 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 14.5 Megapixels
Effective pixel number of camera:
Approx. 14.1 Megapixels
Lens: Carl Zeiss Vario-Tessar 4 × zoom lens
f = 4.7 mm – 18.8 mm (26 mm – 105 mm 
(35 mm film equivalent))
F2.7 (W) – F5.7 (T)
Exposure control: Automatic exposure,
Scene Selection (10 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Incandescent, Flash
Underwater White Balance: Auto,
Underwater 1/2
Recording interval for Burst mode:
Approx. 1.0 second
File format: 
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.21) compliant, DPOF compatible
Movies: AVI (Motion JPEG)
Recording media: Internal Memory
(Approx. 28 MB), “Memory Stick Duo” media, 
SD memory cards,
SDHC memory cards (Class 4, 6,10)
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index) set to Auto):
Approx. 0.3 m to 3.5 m (W)
(11 7/8 inches to 11 feet 5 7/8 inches)
Approx. 0.6 m to 1.8 m (T) (1 foot 11 5/8 inches 
to 5 feet 10 7/8 inches)
[Input and Output connectors]
(USB)/A/V OUT terminal:
Video output
Audio output (Monaural)
USB communication
USB communication: Hi-Speed USB
(USB 2.0 compliant)
[LCD screen]
LCD panel: 
6.7 cm (2.7 type) TFT drive
Total number of dots: 230 400 (960 × 240) dots
[Power, general]
Power: Rechargeable battery pack
NP-BN1, 3.6 V
Power consumption (during shooting):
1.0 W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions: 
92.9 × 51.9 × 17.3 mm 
(3 3/4 × 2 1/8 × 11/16 inches) 
(W/H/D, excluding protrusions)
Mass (including NP-BN1 battery pack,
Memory card):
Approx. 117 g
(4.1 oz.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
Compatible
PictBridge: Compatible
BC-CSN/BC-CSNB battery charger
Power requirements: AC 100 V to
240 V, 50/60 Hz, 2 W
Output voltage: DC 4.2 V, 0.25 A
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions: Approx. 55 × 24 × 83 mm
(2 1/4 × 31/32 × 3 3/8 inches)
(W/H/D)
Mass: Approx. 55 g (1.9 oz.)
Rechargeable battery pack 
NP-BN1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 0.9 A
Capacity: 
typical: 2.3 Wh (630 mAh)
minimum: 2.2 Wh (600 mAh)
Design and specifications are subject to change 
without notice.
本体
[システム]
撮像素子:7.76 mm(1/2.3型)カラー 
CCD原色フィルター
総画素数:約1448万画素
カメラ有効画素数:約1414万画素
レンズ:カール ツァイス バリオ テッサー
4倍ズームレンズ
f=4.7 mm ∼ 18.8 mm
(26 mm ∼ 105 mm(35 mmフィルム
換算値))、F2.7(W)∼ F5.7(T)
露出制御:自動、シーンセレクション
(10 モード)
ホワイトバランス:オート、太陽光、曇天、
蛍光灯1、2、3、電球、フラッシュ
水中ホワイトバランス:オート、水中1、2
連写の撮影間隔:約1.0秒 
記録方式: 
静止画:JPEG(DCF Ver. 2.0、Exif
Ver. 2.21)準拠、DPOF対応
動画:AVI(Motion JPEG)
記録メディア:内蔵メモリー 約28 MB、
“メモリースティック デュオ”、SD
メモリーカード、SDHCメモリーカード
(Class 4、6、10)
フラッシュ:撮影範囲(ISO感度(推奨露 光指数)が
オートのとき)
約0.3 m∼ 3.5 m(W)/約0.6 m∼ 1.8 m(T)
[入出力端子]
(USB)・A/V OUT端子
映像出力
音声出力(モノラル)
USB通信
USB通信:Hi-Speed USB(USB 2.0準拠)
[液晶画面]
液晶パネル:6.7 cm(2.7型)、TFT駆動
総ドット数:230 400(960×240)ドット
[電源・その他]
電源:リチャージャブルバッテリーパック
NP-BN1、3.6 V
消費電力(撮影時):1.0 W
動作温度:0 ℃∼ 40 ℃
保存温度:−20 ℃∼ +60 ℃
外形寸法:92.9×51.9×17.3 mm
(幅×高さ×奥行き、突起部を除く)
本体質量(バッテリー NP-BN1、メモリー
カードを含む):
約117 g
マイクロホン:モノラル
スピーカー:モノラル
Exif Print:対応
PRINT Image Matching III:対応
PictBridge:対応
バッテリーチャージャー BC-CSN/BC-CSNB
定格入力:AC 100 V ∼ 240 V、
50/60 Hz、2 W
定格出力:DC 4.2 V、0.25 A
動作温度:0 ℃∼ 40 ℃
保存温度:−20 ℃∼ +60 ℃
外形寸法:約55×24×83 mm(幅×高さ×奥行き)
本体質量:約55 g
リチャージャブルバッテリー
パックNP-BN1
使用電池:リチウムイオン蓄電池
最大電圧:DC 4.2 V
公称電圧:DC 3.6 V
容量:2.3 Wh(630 mAh)
本機や付属品の仕様および外観は、改良のため予告
なく変更することがありますが、ご了承ください。
DSC-W320_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS 
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE 
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS 
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS 
PUBLISHED BY SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE 
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY 
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU 
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree 
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with 
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•   Unleaded solder melts at a temperature about 40°C higher than 
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to 
about 350°C.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!
•   Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than 
ordinary solder so use caution not to let solder bridges occur such 
as on IC pins, etc.
•   Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes 
and bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to 
the customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs 
of deterioration. Point them out to the customer and recommend 
their replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Keep the temperature of the soldering iron around 270°C 
during repairing.
 
•   Do not touch the soldering iron on the same conductor of the 
circuit board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering 
or unsoldering.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャ
ビネット,シャーシ,部品などにラベルや捺印で注意
事項を表示しています。これらの注意書き及び取扱説
明書等の注意事項を必ずお守り下さい。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を
持ったものとなっています。従って交換部品は,使用
されていたものと同じ特性の部品を使用して下さい。
特に回路図,部品表に0印で指定されている安全上重
要な部品は必ず指定のものをご使用下さい。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用した
り,プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
熱部品や高圧部品に接近しないよう配慮されています
ので,これらは必ずもとどおりにして下さい。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとど
おりになっているか,またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し,安
全性が確保されていることを確認して下さい。
5.  チップ部品交換時の注意
 
・ 取外した部品は再使用しないで下さい。
 
・ タンタルコンデンサのマイナス側は熱に弱いため交
換時は注意して下さい。
サービス,点検時には次のことにご注意ください。
6.  フレキシブルプリント基板の取扱いについて
 
・ コテ先温度を270℃前後にして行なって下さい。
 
・ 同一パターンに何度もコテ先を当てないで下さい。
(3回以内)
 
・ パターンに力が加わらないよう注意して下さい。
7.  無鉛半田について
 
無鉛半田を使用している基板には,無鉛(Lead  Free)を
意味するレッドフリーマークがプリントされています。
  (注意:基板サイズによっては,無鉛半田を使用してい
てもレッドフリーマークがプリントされていな
いものがあります)
:レッドフリーマーク
無鉛半田には,以下の特性があります。
・   融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能ですが,
少し長めにこてを当てる必要があります。温度調節機能
のついた半田こてを使用する場合,約350℃に設定して
下さい。
注意: 半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して下さ
い。
・   粘性が強い
従来の半田よりも粘性が強いため,IC端子などが半田ブ
リッジしないように注意して下さい。
・   従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが,従来
の半田を追加しても構いません。
– ENGLISH –
– JAPANESE –
DSC-W320_L2
1-1
1. SERVICE  NOTE
1-1.  PRECAUTION ON REPLACING THE SY-244 BOARD
RESTORE DATA
When you replace to the repairing board, get the acquire data from the former needed for the adjustment.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB Serial No.
• AWB standard data input & check,Color reproduction check
Regarding the PMB Portable
PMB Portable has been written in internal memory.
SY-244 board for service is supplied with written the PMB Portable.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “Destination data write”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB serial No. input”.
1-2.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1:  When replacing the SY-244 board, erase the data in internal memory of the board before replacement.
Note 2:   When replacing the SY-244 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a memory card.
1
Insert a memory card with sufficient free capacity into the camera.
2
MENU
t
  
(Settings) 
t
 
 (Memory Card Tool) 
t
 [Copy] 
t
 [OK] 
t z
 on the control button
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• Images cannot be copied individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 
internal memory, remove the memory card after copying, then format the internal memory ([Format] in 
[Internal Memory Tool]).
• A new folder is created on the memory card and all the data will be copied to it. You cannot choose a 
specific folder and copy images to it.
Notes
– ENGLISH –
Method for Formatting the Internal Memory or Memory Card
Format
Formats the memory card or the internal memory. When you use a memory card with this 
camera for the first time, it is recommended to format the card using the camera for stable 
performance of the memory card before shooting. Note that formatting permanently erases all
data on the memory card, and is unrecoverable. Save precious data on a computer, etc.
1
MENU
t
  
(Settings) 
t
 
 (Memory Card Tool) or 
 (Internal 
Memory Tool) 
t
 [Format] 
t
 [OK] 
t z
 on the control button
• Note that formatting permanently erases all data including even protected images.
Note
1-3.  HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust 
Station.
Data writing method
1)   Start the Adjust Manual from the Adjust Station.
2)   Click 
(Write Enable Tool) button.
3)   Click “Activate Write Enable Mode” button.
4)   Upon completion of the setting change, the following message will be displayed.
5)   Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6)   Write the data read out into the PC to the internal memory of the camera.
7)   Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
Page of 32
Display

Download Sony DSC-W320 (serv.man2) Service Manual (Repair Manual)

Here you can read online and download Sony DSC-W320 (serv.man2) Service Manual in PDF. DSC-W320 (serv.man2) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DSC-W320 (serv.man2) Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.