Read Sony DSC-S60 / DSC-S80 / DSC-S90 / DSC-ST80 (serv.man12) Service Manual online
Auto-ADJ
SERVICE MANUAL
DSC-S60/S80/S90/ST80
Ver 1.1 2005.11
Sony EMCS Co.
9-876-869-94
2005K0500-1
© 2005.11
Published by DI Technical Support Department
CORRECTION-1
We will inform you that there are printing errors
in the service manual previously issued.
• Correction of the Before starting adjustment
• Correction of the Table 6-1-1
• Correction of the Service tool
• Correction of the Table 6-1-1
• Correction of the Service tool
DSC-S60/S80/S90/ST80
— 2 —
DSC-S60/S80/S90/ST80
!
: Points deleted portion.
SECTION 6
ADJUSTMENTS
Before starting adjustment
(Service Manual Page 6-1)
(The same model of the same destination)
(Machine to be repaired)
PC
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked.)
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 when replacing board.
Perform either procedure 1 or procedure 2 when replacing board.
PC
Procedure 2
When the data cannot be saved due to defective flash memory, or when the flash memory cannot be removed or
installed, save the data from the same model of the same destination, and download it.
installed, save the data from the same model of the same destination, and download it.
PC
Save the EVR data
to a personal computer.
to a personal computer.
Download the saved
data to a machine.
data to a machine.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board
is replaced.
is replaced.
(Machine after a board is replaced)
(Machine before starting repair)
Download the data.
Save the data.
(Machine to be repaired)
^
— 3 —
DSC-S60/S80/S90/ST80
Precaution on Replacing the SY-126 board
• The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not
required.
• Perform “VIDEO OUT Default Data and Exif Model Data Check” mentioned below, and also the adjustment items
necessary after SY Board replacement.
VIDEO OUT Default Data and Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif
Model Data) is right. If not, rewrite to the right value.
When the data has changed because of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif
Model Data) is right. If not, rewrite to the right value.
VIDEO OUT Default Data
Exif Model Data
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data.
3) Select page: 8F, address: E5 to E7, and set the Exif Model Data.
4) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data.
3) Select page: 8F, address: E5 to E7, and set the Exif Model Data.
4) Click
[Save]
on the SEUS screen.
5) Wait for more than 3 sec.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
Address
8D
A2
Page
4F
4F
Data
NTSC
00
00
PAL
01
01
Address
E5
E6
E7
Page
8F
8F
8F
Data
DSC-S60
36
30
00
DSC-S80
38
30
00
DSC-S90
39
30
00
DSC-ST80
54
38
30
&
: Points added portion.
+
— 4 —
DSC-S60/S80/S90/ST80
Replaced parts
Block
Mounted parts
Board
replacement
replacement
replacement
Adjusting item
Adjustment
LCD unit
Back light unit
(CCD imager)
(T
iming gen., CCD signal process)
(AF illumination LED)
(Camera DSP)
(V
ideo amp.)
(32M
AND flash) (Note 4)
LCD901
D901
IC001
IC101
D002
IC101
IC103
IC301
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE) (Note 3, 4)
Lens block
Flash unit
LCD block
LCD block
CD-573 board
CH-169 board
ST
-122 board
SY
-126 board
SY
-126 board
SY
-126 board
CD-573 board
CH-169 board
ST
-122 board
SY
-126 board
(Note 1)
Initialization of data
z
VIDEO adjustment
Video output level adj.
z
z
z
CAMERA adjustment 1
Flange back adj.
z
z
z
z
CAMERA adjustment 2
Flange back check
z
z
z
z
F No. compensation
Measure gain adj.
Mechanical shutter adj.
Light value adj.
(Note 2)
AWB 3200K-5800K standard data input
z
z
z
z
z
z
Color reproduction adj. & check
CCD linearity check
CCD white defect compensation check
CCD black defect compensation check
Strobe adj.
Auto focus illumination check
COM AC adj.
V-COM adj.
White Balance adj.
CAMERA adjustment 4
CAMERA adjustment 3
z
z
z
z
z
z
CAMERA adjustment 5
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
LCD adjustment
z
z
z
1-1. Adjusting items when replacing main parts and boards
(Service Manual Page 6-3)
When replacing main parts and boards, adjust the items indicated by z in the following table.
Note 1:
The automatic Adjustment Program does not support the “Initialization of data”. Perform it manually.
Note 2:
Use the AWB Adjustment Program (S60S80ST80S90AwbAdjustment.exe).
Note 3:
When replacing the SY-126 board, erase the data in internal memory of the board before replacement.
Note 4:
When replacing the SY-126 board or the IC301 on the SY-126 board, execute formatting and initialize the internal memory after
replacement.
replacement.
Table 6-1-1
!
: Points deleted portion.
@
