Read Sony DSC-S60 / DSC-S80 / DSC-S90 / DSC-ST80 (serv.man7) Service Manual online
SERVICE MANUAL
LEVEL
2
DSC-S60/S80/S90/ST80_L2
Ver. 1.4 2007.10
Sony EMCS Co.
9-876-869-83
2007J0500-1
© 2007.10
Published by Kohda TEC
SUPPLEMENT-2
File this supplement with the service manual.
(DI07-158)
DSC-S60/S80/S90/ST80
DSC-S60/S90
US Model
Canadian Model
Chinese Model
Tourist Model
DSC-S60/S80/S90/
ST80
AEP Model
UK Model
E Model
Hong Kong Model
DSC-S60/S80/S90
Australian Model
Korea Model
DSC-S90
Argentine Model
• Addition of “2-5. ZOOM MOTOR UNIT REPLACEMENT
AND INSPECTION PROCEDURES”
• Change of Repair Parts
• Revision of Accessories
• Revision of Accessories
Note: Please refer to Ver.1.4 of SERVICE MANUAL (9-876-869-31) for the revision of accessories.
— 2 —
DSC-S60/S80/S90/ST80_L2
2-5. ZOOM MOTOR UNIT REPLACEMENT AND INSPECTION PROCEDURES
Service parts
Part Number
Part Name
Quantity
1
2-891-376-01
MOTOR UINT, ZOOM
1
Note: These parts are not prepared as service parts.
Recycle removed screws.
1
Remove solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
2
Remove two screws that fix “Motor Unit, Zoom”.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
3
Confirming Zoom function manually.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
2. DISASSEMBLY
1
not supplied (Note)
Zoom Motor Unit
Two Screws
Solder
Rotate lens barrel and stroke
Length of gear
All circumferences
— 3 —
DSC-S60/S80/S90/ST80_L2
4
Throw in each gear of the new Motor Unit, Zoom, and fix with two screws.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
5
Solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
6
Assemble lens to the unit.
7
Execute the necessary adjustment items referring to Service Manual, ADJ.
8
Final inspection
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
Zoom Motor Unit
Two Screws
Solder
Lens stored
Lens at TELE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
— 4 —
DSC-S60/S80/S90/ST80_L2
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
MC-153 FLEXIBLE BOARD (MULTI CONNECTOR)
(Service manual page 4-31, Location A-3 to F-5)
(Service manual page 4-31, Location A-3 to F-5)
• Change of Repair Parts
: Points changed portion.
Former
New
VMZ6.8NT2L
D003
3
2
1
VMZ6.8NT2L
D002
3
2
1
D001
MAZS068008SO
0
R003
XX
D003
3
2
1
XX
D002
3
2
1
D001
XX
0
R003