Read Sony DSC-S5000 (serv.man2) Service Manual online
DSC-S5000_ADJ
5-5
5-2-2. Zoom Adjustment
The Zoom Over Run/Focus Back Lash Adjustment order is as follows.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
The adjustment finished normally.
O Zoom Station Passed
The adjustment is complete
The adjustment is finished abnormally.
X Focus backlash NG
X Zoom Adjust NG
X Zoom Adjust NG
Malfunction of Zoom adjust-
ment result
ment result
X Focus backlash NG
Malfunction of Zoom adjust-
ment Focus section
ment Focus section
X Zoom Adjust NG
Malfunction of Zoom adjust-
ment Zoom section
ment Zoom section
Adjustment order
Screen display
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in the horizontal plane.
Press the control button “ V (Key Down)”, then Zoom Adjustment starts.
on the screen. (Fig. 5-2-15)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-16 to 5-2-18)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
5-2-3. Far Focus Adjustment
Note:
When using the Flange back adjustment jig, take care of the following points:
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1) Install the Flange back adjustment jig so that the distance between
it and the front of lens of camera is 3 cm or less.
Note:
Note:
Take care not to hit the Flange back adjustment jig when extend-
ing the lens.
2) Make the height of Flange back adjustment jig and the camera equal.
3) Check that the center of chart meets the center of shot image screen
with the zoom lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Far Focus Station Passed
Please Key MENU Enter...
Please Key MENU Enter...
The adjustment is complete
The adjustment is finished abnormally.
X Far Focus NG !
Please ReAdjust Far Focus
Please ReAdjust Far Focus
Malfunction of Far Focus adjust-
ment
ment
Adjustment order
Screen display
3 cm or less
Equipment required: Flange back adjustment jig
Flange back adjustment jig
Camera
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flange back adjustment jig. (Fig. 5-2-19)
Press the control button “ b (Key Left)”, then Far Focus Adjustment starts.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-20)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-20)
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-21)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
Fig. 5-2-15
Fig. 5-2-16
Fig. 5-2-17
Fig. 5-2-18
Fig. 5-2-19
Fig. 5-2-20
Fig. 5-2-21
Click on the first or last page to see other DSC-S5000 (serv.man2) service manuals if exist.