Read Sony DSC-S40 (serv.man14) Service Manual online
• Reference No. search on printed wiring boards is available.
• Method for Copying or Erasing the Data in Internal Memory.
• The Method of Attachment of FP-176 Flexible Board.
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
circuit board replacement service and not intended repair inside the
CH-169 and SY-116 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-169 and SY-116 boards are not shown.
The following pages are not shown.
Printed wiring boards ................ Pages 4-37 to 4-40
Waveforms ................................ Pages 4-49
Mounted parts location .............. Pages 4-50
Electrical parts list ..................... Pages 5-6 and 5-8 to 5-11
CCD, Primary color filter
when converted to a 35 mm still
F2.8 - 5.1
Automatic ND filter switching
JPEG compliant, DPOF
Movies: MPEG1 compliant
set to Auto): 0.2 m to 3.8 m
(7 7/8 inches to 12 feet 5 19/32
inches) (W)/0.5 m to 2.1 m
(19 11/16 inches to 6 feet
10 11/16 inches) (T)
(2), 3 V
HR 15/51:HR6 (size AA)
Nickel-Metal Hydride batteries
(2, not supplied), 2.4 V
ZR6 (size AA) Oxy Nickel
Primary Battery (2, not
supplied), 3 V
AC-LS5K AC Adaptor (not
supplied), 4.2 V
(during shooting with the LCD screen on)
(including two batterries and
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
connections. Check the entire board surface for solder splashes
"pinched" or contact high-wattage resistors.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
circuit board (within 3 times).
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Replace only with the same or equivalent type.
Charging Capacitor (C901) ············································· 1-1
Memory ··········································································· 1-3
SW-437 BOARD (CONTROL SWITCH) ···················· 4-27
ST-116 BOARD (FLASH DRIVE) ······························ 4-29
(MEMORY STICK CONNECTOR) ···························· 4-31
(LENS COVER MOTOR) ············································ 4-31
CONTROL SWITCH BLOCK (RL51320) ·················· 4-32
FP-176 FLEXIBLE ······················································· 4-47
5-1-2. BT Holder Block ····························································· 5-3
5-1-3. Batery Holder Section ··················································· 5-4