Read Sony DSC-H100 Service Manual online
DSC-H100
1-2E
1-4. PRECAUTION ON REPLACING THE LENS BLOCK ASSY
The slant of the CCD Block Assy is adjusted with the Lens L Washers, the Lens O Washers and the CCD Rubber 0.5mm in the Lens Block Assy.
After the Lens Block Assy is replaced, select and install Lens L Washers Lens O Washers CCD Rubber 0.5mm according to the following.
After the Lens Block Assy is replaced, select and install Lens L Washers Lens O Washers CCD Rubber 0.5mm according to the following.
Screws
CCD Block Assy
Lens Block Assy
Lens O Washers
Lens L Washers
CCD Rubber 0.5mm
Filter Mask
Washer height values A, B, and C are described on the QR Code Label attached to the Lens Block Assy. (A, B, and C show installation positions of
O Washers.)
Combinations of these values are grouped into two types:
a type that uses CCD Rubber 0.5mm and a type that does not use CCD Rubber 0.5mm. Install washers according to the washer installation method
for each type.
O Washers.)
Combinations of these values are grouped into two types:
a type that uses CCD Rubber 0.5mm and a type that does not use CCD Rubber 0.5mm. Install washers according to the washer installation method
for each type.
01604750
924
XX
XX
XX
A
B
C
QR Code Label
QR Code Label
Values of Lens O Washers
B
A
C
Lens O Washers
Lens O Washers installation locations
Lens L Washers
1. Deciding washer installation type
• Type that uses CCD Rubber 0.5mm
a) Two values out of three values are 60 or more.
A
B
C
60
65
45
b) One value out of three values is 80 or more and other two values are between 50 and 60.
Example)
Example)
A
B
C
50
55
80
Install washers according to “2. An example of installing washers of the type that uses CCD Rubber 0.5mm.”
• Type that does not use CCD Rubber 0.5mm
a) Three values are less than 50.
Example)
Example)
A
B
C
30
25
35
Install washers according to “3. An example of installing washers of the type that does not use CCD Rubber 0.5mm.”
There are the following types of Lens L Washers and Lens O Washers.
Lens L Type Washer
Lens L Type Washer
Part Number
t (mm)
4-447-203-01 0.05
4-447-204-01 0.1
4-447-205-01 0.15
4-447-206-01 0.2
4-447-204-01 0.1
4-447-205-01 0.15
4-447-206-01 0.2
Lens O Type Washer
Part Number t (mm)
4-447-208-01 0.05
4-447-209-01 0.1
4-447-211-01 0.15
4-447-212-01
4-447-208-01 0.05
4-447-209-01 0.1
4-447-211-01 0.15
4-447-212-01
0.2
2. An example of installing washers of the type that uses CCD Rubber 0.5mm
Example)
Example)
A
B
C
60
65
45
(1) Install the CCD Rubber 0.5mm and the Filter Mask.
(2) The minimum value among values at three locations (A, B, and C) is 45.
(2) The minimum value among values at three locations (A, B, and C) is 45.
Therefore, install the following Lens L Washers corresponding to a thickness of 0.45 mm.
Lens L Washer (0.2mm) x 2
Lens L Washer (0.05mm) x 1
(3) The value at A is 60 and the difference from the value at C is 15, which corresponds to 0.15 mm.
Therefore, install the following Lens O Washer at location A.
Lens O Washer (0.1mm) x 1
Lens O Washer (0.05mm) x 1
(4) The value at B is 65 and the difference from the value at C is 20, which corresponds to 0.2 mm.
Therefore, install the following Lens O Washer at location B.
Lens O Washer (0.1mm) x 2
QR Code Label
01604750
924
60
65
45
A
B
C
A
B
C
Lens O Washer 0.1
(4-447-209-01)
(4-447-209-01)
Lens O Washer 0.05
(4-447-208-01)
(4-447-208-01)
Lens L Washer 0.2
(4-447-206-01)
(4-447-206-01)
Lens L Washer 0.05
(4-447-203-01)
(4-447-203-01)
Lens O Washer 0.1
(4-447-209-01)
(4-447-209-01)
CCD Rubber 0.5mm
Filter Mask
3. An example of installing washers of the type that does not use CCD Rubber 0.5mm
Example)
Example)
A
B
C
30
25
35
(1) Install the Filter Mask.
(2) The minimum value among values at three locations (A, B, and C) is 25. Therefore, install the following Lens L Washers corresponding to a
(2) The minimum value among values at three locations (A, B, and C) is 25. Therefore, install the following Lens L Washers corresponding to a
thickness of 0.25 mm.
Lens L Washer (0.1mm) x 1
Lens L Washer (0.15mm) x 1
(3) The value at A is 30 and the difference from the value at B is 5, which corresponds to 0.05 mm.
Therefore, install the following Lens O Washer at location A.
Lens O Washer (0.05mm) x 1
(4) The value at C is 35 and the difference from the value at B is 10, which corresponds to 0.1 mm.
Therefore, install the following Lens O Washer at location C.
Lens O Washer (0.1mm) x 1
QR Code Label
01604750
924
30
25
35
A
B
C
A
B
C
Lens O Washer 0.05
(4-447-208-01)
(4-447-208-01)
Lens L Washer 0.1
(4-447-204-01)
(4-447-204-01)
Lens L Washer 0.15
(4-447-205-01)
(4-447-205-01)
Lens O Washer 0.1
(4-447-209-01)
(4-447-209-01)
Filter Mask
Ver. 1.1 2012.10
Click on the first or last page to see other DSC-H100 service manuals if exist.