DSC-H100 - Sony Digital Camera Service Manual (repair manual). Page 2

DSC-H100

– 2 –

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.

After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.

1.  Check the area of your repair for unsoldered or poorly-soldered 

connections. Check the entire board surface for solder splashes and 
bridges.

2.  Check the interboard wiring to ensure that no wires are “pinched” 

or contact high-wattage resistors.

3.  Look for unauthorized replacement parts, particularly transistors, 

that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.

4.  Look for parts which, through functioning, show obvious signs of 

deterioration. Point them out to the customer and recommend their 
replacement.

5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 

•   Keep the temperature of the soldering iron around 350°C during 

repairing.

 

•   Do not touch the soldering iron on the same conductor of the circuit 

board (within 3 times).

 

•   Be careful not to apply force on the conductor when soldering or 

unsoldering.

Danger of explosion occurs if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

This unit uses unleaded solder. 
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 

lead free mark due to their particular size.)

Be careful to the following points to solder or unsolder.

•  Set the soldering iron tip temperature to 350°C approximately.
 

If cannot control temperature, solder/unsolder at high temperature 
for a short time.

 

Caution: The printed pattern (copper foil) may peel away if the 

heated tip is applied for too long, so be careful!

 

 

Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.

•  Be sure to control soldering iron tips used for unleaded solder and 

those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.

Image device: 7.75 mm (1/2.3 type)
 

color CCD, Primary color filter

Total pixel number of camera:
 

Approx. 16.4 Megapixels

Effective pixel number of camera:
 

Approx. 16.1 Megapixels

Lens: 21× zoom lens
 

f = 4.5 mm – 94.5 mm (25 mm –

 

525 mm (35 mm film equivalent))

 

F3.1 (W) – F5.8 (T)

SteadyShot: Optical
Exposure control: Automatic exposure,
 

Manual Exposure, Scene Selection

 (11 

modes)

White balance: Automatic, Daylight,
 

Cloudy, Fluorescent 1/2/3,

 

Incandescent, Flash, One Push

Recording interval for Burst mode:
 

Approx. 1.0 second

File format:
 

Still images: JPEG (DCF, Exif,

 

MPF Baseline) compliant, DPOF

 compatible
 Movies: 

MPEG-4 

AVC/H.264

Recording media: Internal Memory
 

(Approx. 55 MB), “Memory Stick

 

Duo” media, “Memory Stick

 

Micro” media, SD cards, microSD

 memory 

cards

Flash: Flash range (ISO sensitivity
 

(Recommended Exposure Index)

 set 

to 

Auto):

 

Approx. 0.5 m to 6.8 m (W) (1 ft.

 

7 3/4 inches to 22 ft. 3 3/4 inches)

 

Approx. 0.5 m to 3.7 m (T) (1 ft.

 

7 3/4 inches to 12 ft. 1 3/4 inches)

USB / A/V OUT jack:
 Video 

output

 Audio 

output

 USB 

communication

USB communication: Hi-Speed USB
 (USB 

2.0)

LCD screen:
 

7.5 cm (3.0 type) TFT drive

Total number of dots:
 

460 800 dots

Power: LR6 (size AA) alkaline
 

batteries (4), 6 V

 

HR15/51: HR6 (size AA) Nickel-

 

Metal Hydride batteries (4) (sold

 separately), 

4.8 

V

 ZR6 

(size 

AA)

Power consumption (during shooting):
 1.4 

W

Operating temperature:
 

0°C to 40°C (32°F to 104°F)

Storage temperature:
 

–20°C to +60°C (–4°F to +140°F)

Dimensions (CIPA compliant):
 

122.9 mm × 83.2 mm × 81.3 mm

 

(4 7/8 inches × 3 3/8 inches ×

 

3 1/4 inches)

 (W/H/D)
Mass (CIPA compliant) (including four
 

batteries and “Memory Stick Duo”

 media):
 

Approx. 515 g (1 lb 2.2 oz)

Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
 Compatible

Design and specifications are subject to
change without notice.