Read Sony XSP-N1BT Service Manual online
XSP-N1BT
24
Installing the microphone (
)
To capture your voice during handsfree calling, you
need to install the microphone ͭ.
need to install the microphone ͭ.
Cautions
ˎ Keep the microphone away from extremely high
temperatures and humidity.
ˎ It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from obstructing
your driving.
Be sure to keep it and other parts from obstructing
your driving.
ˎ If airbags or any other shock-absorbing equipment
is in your car, contact the store where you
purchased this unit, or the car dealer, before
installation.
purchased this unit, or the car dealer, before
installation.
Ǻ-A Installing on the sun visor
Install clips (not supplied) and adjust the length and
position of the cord so that it does not obstruct your
driving.
position of the cord so that it does not obstruct your
driving.
Ǻ-B Installing on the dashboard
Install a clip (not supplied) and adjust the length and
position of the cord so that it does not obstruct your
driving.
position of the cord so that it does not obstruct your
driving.
Notes
ˎ Before attaching the double-sided tape , clean
the surface of the dashboard with a dry cloth.
ˎ Adjust the microphone angle to the proper
position.
Notes on the tuning step
ˎ For how to set the tuning step, see the supplied
Operating Instructions.
ˎ If replacing the car battery or changing the
connections, the tuning step setting will be erased.
Ǹ-B Mounting the unit in a Japanese car
You may be able to install this unit in some makes of
Japanese cars without the supplied bracket. If you
cannot, consult your Sony dealer.
Japanese cars without the supplied bracket. If you
cannot, consult your Sony dealer.
When mounting this unit to the preinstalled brackets
of your car, use the supplied screws ʙ in the
appropriate screw holes, based on your car: T for
TOYOTA, M for MITSUBISHI and N for NISSAN.
of your car, use the supplied screws ʙ in the
appropriate screw holes, based on your car: T for
TOYOTA, M for MITSUBISHI and N for NISSAN.
Note
To avoid a malfunction, install only with the supplied screws ʙ.
To avoid a malfunction, install only with the supplied screws ʙ.
Warning if your car’s ignition
has no ACC position
has no ACC position
Be sure to set the AUTO OFF function. For details, see
the supplied Operating Instructions.
The unit will shut off completely and automatically
in the set time after the unit is turned off, which
prevents battery drain.
If you do not set the AUTO OFF function, press and
hold OFF until the display disappears each time you
turn the ignition off.
the supplied Operating Instructions.
The unit will shut off completely and automatically
in the set time after the unit is turned off, which
prevents battery drain.
If you do not set the AUTO OFF function, press and
hold OFF until the display disappears each time you
turn the ignition off.
Fuse replacement (
)
When replacing the fuse, be sure to use one
matching the amperage rating stated on the original
fuse. If the fuse blows, check the power connection
and replace the fuse. If the fuse blows again after
replacement, there may be an internal malfunction.
In such a case, consult your nearest Sony dealer.
matching the amperage rating stated on the original
fuse. If the fuse blows, check the power connection
and replace the fuse. If the fuse blows again after
replacement, there may be an internal malfunction.
In such a case, consult your nearest Sony dealer.
Precautions
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperatures,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
ˎ To prevent hands or the shift lever touching the
unit or smartphone when operating the shift lever,
keep an adequate distance between the unit and
the shift lever.
keep an adequate distance between the unit and
the shift lever.
Mounting angle adjustment
ˎ Mounting in a downward direction is not
supported.
ˎ Adjust the mounting angle to less than 45°.
Removing the bracket (
)
Before installing the unit, remove the bracket ʓ
from the unit.
from the unit.
1
Insert the release keys ʕ into the catches
between the unit and the bracket ʓ at the
same time until they click.
between the unit and the bracket ʓ at the
same time until they click.
2
Pull down the bracket ʓ, then pull up the unit
to separate them.
to separate them.
Mounting the unit (
)
Ǹ-A Mounting the unit with the
supplied bracket
supplied bracket
1
Before installing, make sure that the catches on
both sides of the bracket ʓ are bent inwards
3.5 mm (
both sides of the bracket ʓ are bent inwards
3.5 mm (
5
/
32
in).
2
Position the supplied bracket ʓ inside the
dashboard.
dashboard.
3
Bend the claws outward for a tight fit.
4
Mount the unit onto the supplied bracket ʓ.
Note
If the catches are straight or bent outwards, the unit will not be
installed securely and may spring out.
If the catches are straight or bent outwards, the unit will not be
installed securely and may spring out.
q
B
A
ʕ
ʓ
Face the hook inwards.
B
Bracket
Bracket
to dashboard/center console
ʙ
ʙ
Existing parts supplied with your car
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Claws
ʓ
Catch
Larger than 182 mm (7
1
/
4
in)
Larger than 111 mm (4
3
/
8
in)
Fuse (10 A)
A
Clips (not supplied)
Clip (not supplied)
Location of screw holes
T: TOYOTA
M: MITSUBISHI
N: NISSAN
T: TOYOTA
M: MITSUBISHI
N: NISSAN
Catch
Click on the first or last page to see other XSP-N1BT service manuals if exist.