Read Sony XR-F5100S Service Manual online
5
XR-F5100S
Connection diagram (3)
1
To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
First connect the black earth lead, then connect
the yellow and red power input leads.
2
To the power aerial control lead or power
supply lead of aerial booster amplifier
supply lead of aerial booster amplifier
Notes
•
•
•
It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
in the accessory position of the ignition key
switch
Notes
•
•
•
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
6
To the +12 V power terminal which is energized
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
L
R
BUS AUDIO IN
AUDIO OUT
REAR
*
2
BUS
CONTROL IN
REMOTE
IN
3
from car aerial
2
5
4
AMP REM
7
Left
Right
Left
Right
Max. supply current 0.3 A
Max. supply current 0.1 A
Fuse (10 A)
Red
Yellow
Black
Blue
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
3
1
ANT REM
6
*
3
Source selector
(not supplied )
(not supplied )
XA-C40
Supplied with the CD/MD changer
Light blue
ATT
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched to REAR
or SUB.
For details, see the supplied operating
instructions.
or SUB.
For details, see the supplied operating
instructions.
*
3
Insert with the cord upwards.
*
1
Supplied with XA-C40
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
•
•
When your car has built-in FM/MW/SW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
A power aerial without relay box cannot be used
with this unit.
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (
−) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (
a common negative (
−) lead for the right and left
speakers.
• Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
Click on the first or last page to see other XR-F5100S service manuals if exist.