Read Sony XM-2100GTX Service Manual online
9
9
XM-2100GTX
3-3. IC BLOCK DIAGRAM
IC902 µPC494GS (Main Board)
SECTION 3
DIAGRAMS
3-1. NOTE FOR PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM
3-2. WAVEFORM
— Main Board —
IC902
5
1
1V/DIV, 5µsec/DIV
20µsec
2.8Vp-p
16
15
ERROR
ERROR
14
13
1
2
3
4
5
6
7
8
12
11
10
9
REF.REG.
OSC
0.1V
D101
E-4
D102
E-4
D201
E-5
D202
E-5
D301
G-5
D302
G-5
D303
B-12
D304
C-12
D305
F-6
D306
F-6
D901
G-10
D902
F-9
D903
D-6
D904
F-9
D905
B-12
IC301
H-3
IC302
I-6
IC303
H-6
IC304
G-7
IC901
F-7
IC902
E-9
LED901
F-7
Q101
I-7
Q102
G-4
Q103
E-4
Q104
E-4
Q105
D-4
Q106
D-4
Q107
D-2
Q108
D-3
Q109
B-4
Q110
B-3
Q111
B-3
Q112
C-3
Q113
E-3
Q114
F-3
• Semiconductor Location
(Main Board)
Ref. No.
Location
Ref. No.
Location
Q115
C-3
Q116
E-3
Q201
H-7
Q202
G-5
Q203
E-5
Q204
E-5
Q205
D-6
Q206
D-5
Q207
B-7
Q208
B-7
Q209
B-5
Q210
B-4
Q211
B-9
Q212
B-8
Q213
B-7
Q214
B-5
Q215
B-9
Q216
B-6
Q301
F-5
Q302
F-5
Q303
F-6
Q304
F-6
Q305
E-8
Q306
D-8
Q307
H-4
Q901
G-10
Q902
G-10
Q903
G-10
Q904
F-9
Q905
D-9
Q906
E-9
Q907
F-7
Q908
E-12
Q909
E-11
Q910
F-12
Q911
D-12
Q912
E-12
Q913
D-12
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
%
: indicates tolerance.
•
2
: nonflammable resistor.
Note:
The components identi-
fied by mark
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
•
A
: B+ Line.
•
B
: B– Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from +12V and REM terminals.
• Voltage is dc with respect to ground under no-signal
condition.
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: AUDIO
for printed wiring boards:
Note:
Note:
• X
: parts extracted from the component side.
•
: Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side:
Parts on the parts face side seen from the
(Side A)
parts face are indicated.
Click on the first or last page to see other XM-2100GTX service manuals if exist.