Read Sony XAV-712BT / XAV-712HD Service Manual online
XAV-712BT/712HD
9
(E (NTSC) model)
English
Cautions
Run all gr ound (ear th) leads to a c ommon gr ound
(ear th) point.
This unit is designed f or negative ground (earth) 12 V
DC operation only.
Do not disas semble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a scr ew, or caught in
moving parts (e .g. seat railing).
Before making c onnections, turn the car ignition off
to avoid shor t circuits.
Connect the yellow and red power supply leads
only after all other leads have been c onnected.
Be sur e to insulate any loose unc onnected leads
with electrical tape for saf ety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight
forward; do not install it at a slanted angle .
(ear th) point.
This unit is designed f or negative ground (earth) 12 V
DC operation only.
Do not disas semble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a scr ew, or caught in
moving parts (e .g. seat railing).
Before making c onnections, turn the car ignition off
to avoid shor t circuits.
Connect the yellow and red power supply leads
only after all other leads have been c onnected.
Be sur e to insulate any loose unc onnected leads
with electrical tape for saf ety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight
forward; do not install it at a slanted angle .
Notes on the power supply lead (yellow)
When c onnecting this unit in combination with other
stereo components, the amper age rating of the car
circuit to which the unit is connected must be higher
than the sum of each c omponent's fuse amper age
rating.
If no car circuits are rated high enough, connect the
unit directly to the battery.
stereo components, the amper age rating of the car
circuit to which the unit is connected must be higher
than the sum of each c omponent's fuse amper age
rating.
If no car circuits are rated high enough, connect the
unit directly to the battery.
Connection diagr am
To a common gr ound (ear th) point
First connect the black gr ound (earth) lead, then connect the
yellow and red power supply leads.
yellow and red power supply leads.
To the power antenna (aerial) c ontrol lead or
the power supply lead of the antenna (aerial)
booster
the power supply lead of the antenna (aerial)
booster
Notes
It is not necessar y to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booste r, or with a
manually-oper ated telescopic antenna (aerial).
If your car has a built -in FM/AM antenna (aerial) in the r ear/
side glas s, see “Notes on the c ontrol and power supply leads. ”
antenna (aerial) or antenna (aerial) booste r, or with a
manually-oper ated telescopic antenna (aerial).
If your car has a built -in FM/AM antenna (aerial) in the r ear/
side glas s, see “Notes on the c ontrol and power supply leads. ”
To AMP REMO TE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
system may damage the unit.
To a car’s illumination signal
Be sur e to first connect the black gr ound (earth) lead to a
common gr ound (earth) point.
common gr ound (earth) point.
To the +12 V power terminal which is
ener gized when the ignition switch is set to
the a ccessor y position
ener gized when the ignition switch is set to
the a ccessor y position
Notes
If there is no a ccessory position, connect to the +12 V power
(battery) terminal which is ener gized at all times.
Be sur e to first connect the black gr ound (earth) lead to a
common gr ound (earth) point.
If your car has a built -in FM/AM antenna (aerial) in the r ear/
side glas s, see “Notes on the c ontrol and power supply leads. ”
(battery) terminal which is ener gized at all times.
Be sur e to first connect the black gr ound (earth) lead to a
common gr ound (earth) point.
If your car has a built -in FM/AM antenna (aerial) in the r ear/
side glas s, see “Notes on the c ontrol and power supply leads. ”
To the +12 V power terminal which is
ener gized at all times
ener gized at all times
Be sur e to first connect the black gr ound (earth) lead to a
common gr ound (earth) point.
common gr ound (earth) point.
To the parking br ake switch cord
The mounting position of the parking br ake switch cord depends
on your car. For details, see “Connecting the parking brake lead
(
on your car. For details, see “Connecting the parking brake lead
(
)” on the reverse side .
To an auxiliar y devic e such as a por table
media player , game c onsole , etc. (not
supplied)
media player , game c onsole , etc. (not
supplied)
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
To the +12 V power terminal of the c ar’s rear
lamp lead (only when c onnecting the rear
view c amer a)
lamp lead (only when c onnecting the rear
view c amer a)
Notes on the c ontrol and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn
on the unit.
If your car has built-in FM/AM antenna (aerial) in the r ear/side
glass, connect REM OUT lead (blue/white striped) or the a ccessory
power supply lead (r ed) to the power terminal of the e xisting
antenna (aerial) booste r. For details, consult your dealer.
A power antenna (aerial) without a r elay box cannot be used with
this unit.
on the unit.
If your car has built-in FM/AM antenna (aerial) in the r ear/side
glass, connect REM OUT lead (blue/white striped) or the a ccessory
power supply lead (r ed) to the power terminal of the e xisting
antenna (aerial) booste r. For details, consult your dealer.
A power antenna (aerial) without a r elay box cannot be used with
this unit.
Memor y hold c onnection
When the yellow power supply lead is c onnected, power will always
be supplied to the memor y circuit even when the ignition switch is
turned off.
When the yellow power supply lead is c onnected, power will always
be supplied to the memor y circuit even when the ignition switch is
turned off.
Notes on speak er connection
Before connecting the speak ers, turn the unit off.
Use speak ers with an impedanc e of 4 to 8 ohms, and with
adequate power handling c apacities to avoid damage .
Do not connect the speak er terminals to the c ar chas sis, or connect
the terminals of the right speak ers with those of the left speak ers.
Do not connect the ground (earth) lead of this unit to the negative
(–) terminal of a speak er.
Do not attempt to connect the speak ers in parallel.
Connect only pas sive speak ers. Connecting active speak ers (with
built-in amplifiers) to the speak er terminals may damage the unit.
To avoid a malfunction, do not use the built-in speak er leads
installed in your car if they feature a c ommon negative (–) lead f or
the right and left speak ers.
Do not connect the unit’s speak er leads to each other .
Use speak ers with an impedanc e of 4 to 8 ohms, and with
adequate power handling c apacities to avoid damage .
Do not connect the speak er terminals to the c ar chas sis, or connect
the terminals of the right speak ers with those of the left speak ers.
Do not connect the ground (earth) lead of this unit to the negative
(–) terminal of a speak er.
Do not attempt to connect the speak ers in parallel.
Connect only pas sive speak ers. Connecting active speak ers (with
built-in amplifiers) to the speak er terminals may damage the unit.
To avoid a malfunction, do not use the built-in speak er leads
installed in your car if they feature a c ommon negative (–) lead f or
the right and left speak ers.
Do not connect the unit’s speak er leads to each other .
Notes on c onnection
If [Check Audio Output Wiring] appears in the display , mak e sure
the speak er and amplifier ar e connected correctly.
To use the monitor f or the rear seats, connect the parking brake
switch cord to the ground (earth).
the speak er and amplifier ar e connected correctly.
To use the monitor f or the rear seats, connect the parking brake
switch cord to the ground (earth).
Securing the c onnection of the
HDMI/MHL c onnection c able
HDMI/MHL c onnection c able
Secure the connection between the HDMI/MHL
connection cable and main unit, using the hook and
loop fastener
connection cable and main unit, using the hook and
loop fastener
.
1
Wrap the hook and loop f astener
around the
neck of a c able .
2
Pull the hook and loop f astener
firmly back
around the neck of the other c able .
3
Bring the ends of the hook and loop f astener
together to secur e the c onnection of the c ables.
together to secur e the c onnection of the c ables.
Español
Precauciones
Conecte todos los c ables de c one xión a masa a un
punto común.
Esta unidad ha sido diseñada par a alimentarse
solamente c on cc de 12 V de masa negativ a.
No desmonte ni modifique la unidad.
No instale la unidad en lugar es en los que interfier a
con el funcionamiento del airbag.
No coloque los c ables debajo de ningún tornillo , ni
los aprisione c on partes móviles (p . ej. los raíles del
asiento).
Antes de r ealizar las c onexiones, desactive el
encendido del automóvil par a evitar cortocircuitos.
Conecte los c ables de fuente de alimentación
amarillo y rojo solamente después de haber
conectado los demás.
Por razones de seguridad, asegúr ese de aislar c on
cinta aislante los c ables sueltos que no estén
conectados.
No presione la pantalla L CD cuando instale la
unidad.
Al instalar la unidad, el monitor debe mir ar hacia
adelante; no la instale en un ángulo inclinado .
punto común.
Esta unidad ha sido diseñada par a alimentarse
solamente c on cc de 12 V de masa negativ a.
No desmonte ni modifique la unidad.
No instale la unidad en lugar es en los que interfier a
con el funcionamiento del airbag.
No coloque los c ables debajo de ningún tornillo , ni
los aprisione c on partes móviles (p . ej. los raíles del
asiento).
Antes de r ealizar las c onexiones, desactive el
encendido del automóvil par a evitar cortocircuitos.
Conecte los c ables de fuente de alimentación
amarillo y rojo solamente después de haber
conectado los demás.
Por razones de seguridad, asegúr ese de aislar c on
cinta aislante los c ables sueltos que no estén
conectados.
No presione la pantalla L CD cuando instale la
unidad.
Al instalar la unidad, el monitor debe mir ar hacia
adelante; no la instale en un ángulo inclinado .
Notas sobr e el c able de fuente de alimentación
(amarillo)
(amarillo)
Cuando conecte esta unidad en c ombinación con
otros componentes estéreo , la capacidad nominal
del circuito conectado del automóvil debe ser
superior a la suma del fusible de c ada c omponent e.
Si no hay circuitos del automóvil con capacidad
nominal suficientemente alta, conecte la unidad
directamente a la batería.
otros componentes estéreo , la capacidad nominal
del circuito conectado del automóvil debe ser
superior a la suma del fusible de c ada c omponent e.
Si no hay circuitos del automóvil con capacidad
nominal suficientemente alta, conecte la unidad
directamente a la batería.
Diagrama de c one xiones
A un punto de c one xión a masa c omún
Conecte primero el cable de c onexión a masa negr o, y después
los cables de fuente de alimentación r ojo y amarillo.
los cables de fuente de alimentación r ojo y amarillo.
Al cable de c ontrol de la antena motorizada o
al cable de fuente de alimentación del
amplific ador de señal de la antena
al cable de fuente de alimentación del
amplific ador de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplific ador de
señal de la antena, o se utiliza una antena telesc ópica
accionada manualment e, no será necesario c onectar este
cable.
Si el automóvil tiene una antena FM/AM integr ada en el cristal
posterior o lateral, consulte las “Notas sobr e los cables de
control y de fuente de alimentación” .
señal de la antena, o se utiliza una antena telesc ópica
accionada manualment e, no será necesario c onectar este
cable.
Si el automóvil tiene una antena FM/AM integr ada en el cristal
posterior o lateral, consulte las “Notas sobr e los cables de
control y de fuente de alimentación” .
A AMP REMO TE IN de un amplific ador de
potencia opcional
potencia opcional
Esta conexión es sólo par a amplific adores. La conexión de
cualquier otro sistema puede dañar la unidad.
cualquier otro sistema puede dañar la unidad.
A una señal de iluminación del automóvil
Asegúr ese de c onectar primero el cable de c onexión a masa
negro a un punto de c onexión a masa c omún.
negro a un punto de c onexión a masa c omún.
Al terminal de alimentación de +12 V que
recibe ener gía cuando el interruptor de la
llave de enc endido se c oloca en la posición
de a ccesorio
recibe ener gía cuando el interruptor de la
llave de enc endido se c oloca en la posición
de a ccesorio
Notas
Si no hay posición de a ccesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúr ese de c onectar primero el cable de c onexión a masa
negro a un punto de c onexión a masa c omún.
Si el automóvil tiene una antena FM/AM integr ada en el cristal
posterior o lateral, consulte las “Notas sobr e los cables de
control y de fuente de alimentación” .
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúr ese de c onectar primero el cable de c onexión a masa
negro a un punto de c onexión a masa c omún.
Si el automóvil tiene una antena FM/AM integr ada en el cristal
posterior o lateral, consulte las “Notas sobr e los cables de
control y de fuente de alimentación” .
Al terminal de alimentación de +12 V que
recibe ener gía sin interrupción
recibe ener gía sin interrupción
Asegúr ese de c onectar primero el cable de c onexión a masa
negro a un punto de c onexión a masa c omún.
negro a un punto de c onexión a masa c omún.
Al cable de c onmutación del fr eno de
estacionamient o
estacionamient o
La posición de montaje del c able de c onmutación del fr eno de
estacionamiento depende del automóvil. Para obtener detalles,
vea la sec ción “Conexión del cable del freno de estacionamiento
(
estacionamiento depende del automóvil. Para obtener detalles,
vea la sec ción “Conexión del cable del freno de estacionamiento
(
)” del lado reverso .
A un dispositivo auxiliar , como , por ejemplo ,
un reproductor por tátil, una c onsola de
videojuegos, etc. (no suministr ados)
un reproductor por tátil, una c onsola de
videojuegos, etc. (no suministr ados)
Suger encia
Es posible utilizar el c able con terminales RCA (no suministr ado)
para conectar dispositivos auxiliares.
Es posible utilizar el c able con terminales RCA (no suministr ado)
para conectar dispositivos auxiliares.
Al terminal de alimentación de +12 V del
cable del indic ador posterior del automóvil
(únicamente cuando c onecte la c ámar a
retrovisora)
cable del indic ador posterior del automóvil
(únicamente cuando c onecte la c ámar a
retrovisora)
Notas sobr e los c ables de c ontrol y de fuente de alimentación
El cable REM OUT (r ayado azul y blanc o) suministra cc +12 V al
encender la unidad.
Si el automóvil dispone de una antena de FM/AM inc orporada en el
cristal traser o o lateral, conecte el cable REM OUT (r ayado azul y
blanco) o el cable de fuente de alimentación auxiliar (r ojo) al
terminal de alimentación del amplific ador de señal de la antena
existente. Para obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
encender la unidad.
Si el automóvil dispone de una antena de FM/AM inc orporada en el
cristal traser o o lateral, conecte el cable REM OUT (r ayado azul y
blanco) o el cable de fuente de alimentación auxiliar (r ojo) al
terminal de alimentación del amplific ador de señal de la antena
existente. Para obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Cone xión par a protección de la memoria
Si conecta el c able de fuente de alimentación amarillo , el circuito de
la memoria recibirá siempr e alimentación, aunque apague el
interruptor de encendido.
Si conecta el c able de fuente de alimentación amarillo , el circuito de
la memoria recibirá siempr e alimentación, aunque apague el
interruptor de encendido.
Notas sobr e la cone xión de los altavoc es
Antes de c onectar los altavoc es, desc onecte la alimentación de la
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω c on la capacidad
de potencia adecuada par a evitar que se dañen.
No conecte los terminales de altavo z al chasis del automóvil ni
conecte los terminales de altavo z derecho con los del izquierdo.
No conecte el cable de c onexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoc es en par alelo.
Conecte solamente altavoc es pasivos. Si conecta altavoc es activos
(con amplific adores incorporados) a los terminales de altavo z,
puede dañar la unidad.
Para evitar fallas de funcionamient o, no utilice los cables de altavo z
integrados instalados en el automóvil si la unidad c omparte un
cable negativo c omún (–) para los altavoc es der echo e iz quierdo.
No conecte los c ables de altavo z de la unidad entr e sí.
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω c on la capacidad
de potencia adecuada par a evitar que se dañen.
No conecte los terminales de altavo z al chasis del automóvil ni
conecte los terminales de altavo z derecho con los del izquierdo.
No conecte el cable de c onexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoc es en par alelo.
Conecte solamente altavoc es pasivos. Si conecta altavoc es activos
(con amplific adores incorporados) a los terminales de altavo z,
puede dañar la unidad.
Para evitar fallas de funcionamient o, no utilice los cables de altavo z
integrados instalados en el automóvil si la unidad c omparte un
cable negativo c omún (–) para los altavoc es der echo e iz quierdo.
No conecte los c ables de altavo z de la unidad entr e sí.
Notas sobr e la cone xión
Si en la pantalla apar ece [Verifique el c ableado de salida audio],
verifique que el altavo z y el amplific ador estén c onectados
correctamente.
Si va a utilizar el monitor para los asientos posterior es, conecte el
cable de c onmutación del fr eno de estacionamiento a masa.
verifique que el altavo z y el amplific ador estén c onectados
correctamente.
Si va a utilizar el monitor para los asientos posterior es, conecte el
cable de c onmutación del fr eno de estacionamiento a masa.
*
1
Para obtener detalles sobr e la instalación del
micrófono, consulte “Instalación del micr ófono
(
micrófono, consulte “Instalación del micr ófono
(
)” al reverso .
*
2
Cable con terminales RCA (no suministr ado)
*
3
Cable de conexión HDMI o MHL (suministrados)
*
4
El sonido se emitir á a través de este terminal
sólo cuando esté activ ado ZONE × ZONE. Este
terminal emite a un nivel fijo
independientemente del c ontrol de volumen
de la unidad.
sólo cuando esté activ ado ZONE × ZONE. Este
terminal emite a un nivel fijo
independientemente del c ontrol de volumen
de la unidad.
*
5
Puede requerirse un adaptador independiente.
*
6
Se recomienda utilizar el c able posterior de
USB denominado “HIGH CHARGE” para
recargar la batería de un dispositivo
conectado .
USB denominado “HIGH CHARGE” para
recargar la batería de un dispositivo
conectado .
*
7
Para conectar un teléfono inteligente a la
unidad principal, es nec esario utilizar un cable
adecuado (no suministr ado).
unidad principal, es nec esario utilizar un cable
adecuado (no suministr ado).
*
8
El cable USB posterior sin la etiqueta “HIGH
CHARGE”
CHARGE”
*
9
Entrada HDMI/MHL en el puerto
*
10
Impedancia del altavo z: 4 – 8 Ω × 4
*
1
For details on installing the microphone, see
“Installing the microphone (
“Installing the microphone (
)” on the reverse
side.
*
2
RCA pin cord (not supplied)
*
3
HDMI connection cable or MHL c onnection
cable (supplied)
cable (supplied)
*
4
The sound is output fr om this terminal only
when ZONE × ZONE is activated. This terminal
outputs a fix ed level regardless of the volume
control of the unit.
when ZONE × ZONE is activated. This terminal
outputs a fix ed level regardless of the volume
control of the unit.
*
5
A separ ate adaptor may be required.
*
6
The USB rear cable labeled “HIGH CHARGE” is
recommended to use f or recharging the
battery of a c onnected device.
recommended to use f or recharging the
battery of a c onnected device.
*
7
To connect a smartphone to the main unit, an
appropriate cable (not supplied) is required.
appropriate cable (not supplied) is required.
*
8
The USB rear cable without “HIGH CHARGE”
label
label
*
9
The HDMI in/MHL in port
*
10
Speak er impedanc e: 4 – 8 ohms × 4
Equipment used in illustr ations (not supplied) / Equipo utilizado en las ilustr aciones (no suministr ado)
Subwoof er
Altavo z potenciador de gr aves
Altavo z potenciador de gr aves
Rear speak er
Altavo z posterior
Altavo z posterior
Rear view c amer a
Cámar a retrovisora
Cámar a retrovisora
Monitor
Monitor
Monitor
Power amplifier
Amplific ador de potencia
Amplific ador de potencia
Front speak er
Altavo z frontal
Altavo z frontal
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
HIGH CHARGE
From c ar antenna (aerial)
Desde la antena del automóvil
Desde la antena del automóvil
*
2
REM OUT
Max. supply curr ent: 0.4 A
Corriente máx. de alimentación: 0,4 A
Corriente máx. de alimentación: 0,4 A
ILLUMINATION
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
Blue/white striped
Con rayas azules/blanc as
White
Blanc o
Green
Verde
Verde
Purple
Morado
White/black striped
Con rayas blanc as/negr as
Gray/black striped
Con rayas grises/negr as
Green/black striped
Con rayas ver des/negr as
Gray
Gris
Purple/black striped
Con rayas mor adas/negr as
Black
Negro
Orange/white striped
Con rayas nar anjas/blanc as
PARKING BRAKE
Red
Rojo
Rojo
Yellow
Amarillo
Amarillo
Light green
Verde claro
Verde claro
*
1
*
2
*
6
*
8
*
9
*
3
*
3
*
2
*
2
Smar tphone
Teléfono inteligent e
Smar tphone*
7
, USB devic e
Teléfono inteligente*
7
,
dispositivo USB
*
2
*
2
GND
ACC
BATTERY
or
/
o
*
10
*
1
HDMI connection cable or MHL c onnection cable (supplied)
*
1
Cable de c onexión HDMI o MHL (suministr ados)
*
1
*
1
or
/
o
Smar tphone
Teléfono inteligent e
Asegur ar la cone xión del c able de
cone xión HDMI/MHL
cone xión HDMI/MHL
Asegur e la conexión entre el cable de c onexión HDMI/
MHL y la unidad principal mediante el cierr e de
gancho y laz o
MHL y la unidad principal mediante el cierr e de
gancho y laz o
.
1
Envuelv a el cierr e de gancho y laz o
alrededor
del cuello de un c able .
2
Tire del cierr e de gancho y laz o
hacia atr ás con
firme za par a envolverlo alr ededor del ot ro cable .
3
Una los e xtremos del cierr e de gancho y laz o
para asegur ar la cone xión de los c ables.
para asegur ar la cone xión de los c ables.
Click on the first or last page to see other XAV-712BT / XAV-712HD service manuals if exist.