Read Sony XAV-701BT / XAV-741 Service Manual online
XAV-701BT/741
9
(Sauth African model)
MIC IN*
3
Z×Z L / R*
7
REVERSE IN
CAMERA
REAR OUT
REMOTE IN*
8
SUB OUT
EXT
AUX1 AUDIO
IN
FRONT
AUDIO OUT
REAR
AUDIO OUT
AUX1 IN
AUX2 AUDIO
IN
AUX2 IN
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the power supply connection cable
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the power supply connection cable
to the
unit and speakers before connecting it to the auxiliary
power connector.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
power connector.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
Connection example
Notes (
-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note (
-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
connected to different terminals.
Connection diagram
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
may damage the unit.
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
To the +12 V power terminal of the car’s rear lamp
lead (only when connecting the rear view
camera)
lead (only when connecting the rear view
camera)
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply
connection cable
connecting this unit with the supplied power supply
connection cable
may damage the antenna (aerial).
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V DC when
you turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.
If your car has a built-in FM/MW/LW antenna (aerial) in the rear/side
glass, connect the power antenna (aerial) control lead (blue) or the
accessory power supply lead (red) to the power terminal of the antenna
(aerial) booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
you turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.
If your car has a built-in FM/MW/LW antenna (aerial) in the rear/side
glass, connect the power antenna (aerial) control lead (blue) or the
accessory power supply lead (red) to the power terminal of the antenna
(aerial) booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Notes on connection
If “Output connection failure.” appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
FRONT AUDIO
OUT
SUB OUT
REAR OUT
Z×Z L / R
REAR AUDIO
OUT
AUX IN
( VIDEO )
AUX AUDIO
IN
CAMERA
*
not supplied
Video camera*
A
B
Equipment used in illustrations (not supplied)
Subwoofer
Smartphone
Front speaker
iPod
Rear speaker
Rear view camera
Power amplifier
Monitor
*
1
For details on installing the microphone, see “Installing the microphone
( )” on the
reverse side.
*
2
If your car antenna (aerial) is an ISO (International Organization for Standardization)
type, use the supplied adaptor
type, use the supplied adaptor
to connect it. First connect the car antenna (aerial) to
the supplied adaptor, then connect the adaptor
to the antenna (aerial) jack of the
unit.
*
3
Whether in use or not, route the microphone input cord such that it does not interfere
with driving. Secure the cord with a clamp, etc., if it is installed around your feet.
with driving. Secure the cord with a clamp, etc., if it is installed around your feet.
*
4
RCA pin cord (not supplied)
*
5
For details on connecting to the parking brake switch cord, see “Connecting the parking
brake lead
brake lead
( )” on the reverse side.
*
6
Speaker impedance: 4 – 8 ohms × 4
*
7
The sound is output from this terminal only when ZONE x ZONE is activated. This terminal
outputs a fixed level regardless of the volume control of the unit.
outputs a fixed level regardless of the volume control of the unit.
*
8
A separate adaptor may be required.
*
9
Not supplied
*
10
USB connection cable RC-202IPV (not supplied). To connect an iPod via RC-202IPV, make
sure to connect the video output plug to AUX1 IN.
Blue/white striped
AMP REM
Max. supply current: 0.3 A
Light green
PARKING BRAKE
*
5
From the car’s power connector
For details, see “Power connection diagram” on the reverse side.
From the car’s speaker connector
*
6
Negative polarity positions 2, 4, 6, and 8 have striped leads.
1
Purple
+
Speaker, rear, right
2
–
Speaker, rear, right
3
Gray
+
Speaker, front, right
4
–
Speaker, front, right
5
White
+
Speaker, front, left
6
–
Speaker, front, left
7
Green
+
Speaker, rear, left
8
–
Speaker, rear, left
Positions 1, 2, and 3 do not have pins.
4
Yellow
Continuous power supply
5
Blue
Power antenna (aerial) control
6
Orange/white
Switched illumination power supply
7
Red
Switched power supply
8
Black
Ground (earth)
*
4
*
10
*
10
*
9
*
4
*
4
*
4
*
4
*
4
*
1
Fuse (10 A)
*
2
From car antenna (aerial)
Click on the first or last page to see other XAV-701BT / XAV-741 service manuals if exist.