Read Sony XAV-701BT / XAV-741 Service Manual online
XAV-701BT/741
XAV-701BT/741
8
8
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
Connection example
Notes (
-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note (
-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
connected to different terminals.
Connection diagram
To a common ground (earth) point
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
and red power supply leads.
To the power antenna (aerial) control lead or the
power supply lead of the antenna (aerial) booster
power supply lead of the antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
may damage the unit.
To a car’s illumination signal
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
ground (earth) point.
To the +12 V power terminal which is energized
when the ignition switch is set to the accessory
position
when the ignition switch is set to the accessory
position
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is energized
at all times
at all times
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
ground (earth) point.
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
To the +12 V power terminal of the car’s rear lamp
lead (only when connecting the rear view
camera)
lead (only when connecting the rear view
camera)
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.
If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
connect REM OUT lead (blue/white striped) or the accessory power
supply lead (red) to the power terminal of the existing antenna (aerial)
booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
the unit.
If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
connect REM OUT lead (blue/white striped) or the accessory power
supply lead (red) to the power terminal of the existing antenna (aerial)
booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit’s speaker leads to each other.
Notes on connection
If “Output connection failure.” appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
FRONT AUDIO
OUT
SUB OUT
REAR OUT
Z×Z L / R
REAR AUDIO
OUT
AUX IN
( VIDEO )
AUX AUDIO
IN
CAMERA
*
not supplied
Video camera*
A
B
Equipment used in illustrations (not supplied)
Subwoofer
Smartphone
Front speaker
iPod
Rear speaker
Rear view camera
Power amplifier
Monitor
*
1
Speaker impedance: 4 – 8 ohms × 4
*
2
The microphone is supplied with
XAV-701BT only. For details on installing
the microphone, see “Installing the
microphone (XAV-701BT only) (
XAV-701BT only. For details on installing
the microphone, see “Installing the
microphone (XAV-701BT only) (
)” on
the reverse side.
*
3
The microphone input cord is available
on XAV-701BT only. Whether in use or
not, route the microphone input cord
such that it does not interfere with
driving. Secure the cord with a clamp,
etc., if it is installed around your feet.
on XAV-701BT only. Whether in use or
not, route the microphone input cord
such that it does not interfere with
driving. Secure the cord with a clamp,
etc., if it is installed around your feet.
*
4
RCA pin cord (not supplied)
*
5
For details on connecting to the parking
brake switch cord, see “Connecting the
parking brake lead (
brake switch cord, see “Connecting the
parking brake lead (
)” on the reverse
side.
*
6
not supplied
*
7
The sound is output from this terminal
only when ZONE x ZONE is activated.
This terminal outputs a fixed level
regardless of the volume control of the
unit.
only when ZONE x ZONE is activated.
This terminal outputs a fixed level
regardless of the volume control of the
unit.
*
8
A separate adaptor may be required.
*
9
USB connection cable RC-202IPV (not
supplied). To connect an iPod via
RC-202IPV, make sure to connect the
video output plug to AUX1 IN.
supplied). To connect an iPod via
RC-202IPV, make sure to connect the
video output plug to AUX1 IN.
MIC IN*
3
AUX2 AUDIO
IN
Z×Z L / R*
7
REVERSE IN
CAMERA
REAR OUT
REMOTE IN*
8
SUB OUT
EXT
AUX1 AUDIO
IN
FRONT
AUDIO OUT
REAR
AUDIO OUT
AUX2 IN
AUX1 IN
Fuse (10 A)
From car antenna (aerial)
*
4
REM OUT
Max. supply current: 0.4 A
ILLUMINATION
*
5
PARKING BRAKE
Blue/white striped
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Purple/black striped
Red
Yellow
Black
Orange/white striped
Light green
*
2
*
4
*
6
*
9
*
4
*
4
*
4
*
4
*
1
*
9
XAV-701BT
XAV-701BT only
Left
Right
Left
Right
(E (PAL) model)
Precautions
Choose the installation location carefully so that the unit
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
To open/close the front panel smoothly, insert/eject a
disc easily, and especially to drive safely, a certain
distance between the front panel and the shift lever is
necessary. The necessary distance differs, depending on
the shift lever position of your car. Before installing the
unit, choose the installation location carefully so that
you can drive safely.
will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
To open/close the front panel smoothly, insert/eject a
disc easily, and especially to drive safely, a certain
distance between the front panel and the shift lever is
necessary. The necessary distance differs, depending on
the shift lever position of your car. Before installing the
unit, choose the installation location carefully so that
you can drive safely.
Shift lever
87 mm (3
1
/
2
in)
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake
lead
lead
Be sure to connect the parking brake lead (light green) of
the power supply connection cable
the power supply connection cable
to the parking brake
switch cord. The mounting position of the parking brake
switch cord depends on your car. Consult your car dealer
or your nearest Sony dealer for further details.
switch cord depends on your car. Consult your car dealer
or your nearest Sony dealer for further details.
Installing the microphone
(XAV-701BT only)
(XAV-701BT only)
To capture your voice during handsfree calling, you need
to install the microphone
to install the microphone
.
Cautions
Keep the microphone away from extremely high
temperatures and humidity.
It is extremely dangerous if the cord becomes wound
around the steering column or gearstick. Be sure to keep
it and other parts from obstructing your driving.
If airbags or any other shock-absorbing equipment is in
your car, contact the store where you purchased this
unit, or the car dealer, before installation.
temperatures and humidity.
It is extremely dangerous if the cord becomes wound
around the steering column or gearstick. Be sure to keep
it and other parts from obstructing your driving.
If airbags or any other shock-absorbing equipment is in
your car, contact the store where you purchased this
unit, or the car dealer, before installation.
Parking brake switch cord
Foot brake type
Parking brake switch cord
Hand brake type
A
2
1
2
B
1
b
a
b
a
b
a
Clips (not supplied)
c
b
a
Clip (not supplied)
Face the hook inwards.
-A Installing on the sun visor
1
Install the microphone
a
on the clip
b
.
2
Install the clip
b
on the sun visor.
3
Install clips (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
and position of the cord so that it does not
obstruct your driving.
-B Installing on the dashboard
1
Install the microphone
a
on the clip
b
, then
place the cord along the groove of the clip
b
.
2
Attach the clip
b
to the dashboard with the
double-sided tape
c
.
3
Install a clip (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
and position of the cord so that it does not
obstruct your driving.
Notes
Before attaching the double-sided tape
c
, clean the surface of the
dashboard with a dry cloth.
Adjust the microphone angle to the proper position.
The microphone
Adjust the microphone angle to the proper position.
The microphone
a
can be installed without using the clip
b
.
In this case, directly attach the microphone to the dashboard with the
double-sided tape
double-sided tape
c
. Keep the unused clip
b
for future use.
Removing the bracket
Before installing the unit, remove the bracket
from the unit.
1
Insert both release keys
together between the
unit and the bracket
until they click.
2
Pull down the bracket
, then pull up the unit to
separate them.
Adjusting the frames
You can adjust the projecting part of the unit when the
unit is mounted.
unit is mounted.
Shift lever
Projecting part
1
Remove the screws
from both sides of the unit.
2
Choose a screw hole from
,
or
on each
frame
.
If you secure the frames
with the screw holes
(default position),
it will maximize the projecting part of the unit. On the other hand,
screw holes
screw holes
will minimize the projecting part.
3
Reattach the frames
with the selected screw
holes with the removed screws
.
Notes
Choose the same screw hole position on both frames.
If you intend to secure the frames with screw holes
If you intend to secure the frames with screw holes
or
, make sure
that there is enough space in the dashboard of your car for the unit.
Mounting the unit
-A Mounting the unit with the supplied
bracket
1
1
Position the supplied bracket
inside the
dashboard.
2
Bend the claws outward for a tight fit.
3
Mount the unit onto the supplied bracket
.
-B Mounting the unit in a Japanese car
You may be able to install this unit in some makes of
Japanese cars without the supplied bracket. If you cannot,
consult your Sony dealer.
Japanese cars without the supplied bracket. If you cannot,
consult your Sony dealer.
When mounting this unit to the preinstalled brackets of
your car, use the supplied screws
your car, use the supplied screws
in the appropriate
screw holes, based on your car: T for TOYOTA, M for
MITSUBISHI and N for NISSAN.
MITSUBISHI and N for NISSAN.
Notes
To avoid a malfunction, install only with the supplied screws
.
Do not apply excessive force to the buttons of the unit.
Do not press on the LCD.
Before mounting, make sure there is nothing on the top of the unit.
Do not press on the LCD.
Before mounting, make sure there is nothing on the top of the unit.
Warning if your car’s ignition
has no ACC position
has no ACC position
Be sure to set the Auto Off function. For details, refer to
the supplied “Operating Instructions.”
The unit will shut off completely and automatically in the
set time when no source is selected, which prevents
battery drainage.
If you do not set the Auto Off function, press and hold
the supplied “Operating Instructions.”
The unit will shut off completely and automatically in the
set time when no source is selected, which prevents
battery drainage.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
Reset button
When the installation and connections are completed, be
sure to press the reset button with a ballpoint pen, etc.
sure to press the reset button with a ballpoint pen, etc.
XAV-701BT only
Dashboard
Claws
2
3
1
A
B
Larger than 182 mm (7
1
/
4
in)
Larger than 111 mm (4
3
/
8
in)
To the dashboard/center console
Bracket
Parts supplied with your car
Size:
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Size:
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Bracket
Click on the first or last page to see other XAV-701BT / XAV-741 service manuals if exist.