Read Sony CDX-GT565UV / CDX-GT615UV Service Manual online
CDX-GT565UP/GT565UV/GT615UV
CDX-GT565UP/GT565UV/GT615UV
8
8
(CDX-GT565UP for Wal-Mart model)
Ver. 1.3
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn
on the unit.
on the unit.
When your car has built-in FM/AM antenna (aerial) in the rear/side
glass, connect REM OUT lead (blue/white striped) or the accessory
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
power supply lead (red) to the power terminal of the existing antenna
(aerial) booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned
off.
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned
off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed
in your car if the unit shares a common negative (–) lead for the right
and left speakers.
Do not connect the unit’s speaker leads to each other.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speaker.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed
in your car if the unit shares a common negative (–) lead for the right
and left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE” appears
in the display. In this case, make sure the speaker and amplifier are
connected correctly.
If speaker and amplifier are not connected correctly, “FAILURE” appears
in the display. In this case, make sure the speaker and amplifier are
connected correctly.
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
The use of optical instruments with this product will
increase eye hazard.
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect
the unit directly to the battery.
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect
the unit directly to the battery.
Precauciones
Esta unidad ha sido diseñada para alimentarse sólo con
cc de 12 V de masa negativa.
No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los rieles del
asiento).
Antes de realizar las conexiones, apague el automóvil
para evitar cortocircuitos.
Conecte los cables de fuente de alimentación amarillo
y rojo solamente después de haber conectado los
demás.
Conecte todos los cables de conexión a masa a un
punto común.
Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
El uso de instrumentos ópticos con este producto
aumenta el riesgo de sufrir daños oculares.
cc de 12 V de masa negativa.
No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los rieles del
asiento).
Antes de realizar las conexiones, apague el automóvil
para evitar cortocircuitos.
Conecte los cables de fuente de alimentación amarillo
y rojo solamente después de haber conectado los
demás.
Conecte todos los cables de conexión a masa a un
punto común.
Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
El uso de instrumentos ópticos con este producto
aumenta el riesgo de sufrir daños oculares.
Notas sobre el cable de fuente de alimentación
(amarillo)
(amarillo)
Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
Si no hay circuitos del automóvil con capacidad
nominal suficientemente alta, conecte la unidad
directamente a la batería.
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
Si no hay circuitos del automóvil con capacidad
nominal suficientemente alta, conecte la unidad
directamente a la batería.
Connection example
Notes (
-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
amplifier.
The alarm will only sound if the built-in amplifier is used.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers and a power antenna (aerial).
Connecting any other system may damage the unit.
Connecting any other system may damage the unit.
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
of the car first.
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
in the accessory position of the ignition switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
To the +12 V power terminal which is energized
at all times
at all times
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
of the car first.
A
SIRIUSXM IN
Satellite radio tuner
(SiriusXM)*
Sintonizador de radio por satélite
(SiriusXM)*
* not supplied
no suministrado
no suministrado
B
Ejemplo de conexiones
Notas (
-A)
Asegúrese de conectar primero el cable de conexión a masa antes de
realizar la conexión del amplificador.
La alarma sonará únicamente si se utiliza el amplificador incorporado.
realizar la conexión del amplificador.
La alarma sonará únicamente si se utiliza el amplificador incorporado.
Diagrama de conexión
A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después los
cables amarillo y rojo de fuente de alimentación.
cables amarillo y rojo de fuente de alimentación.
Al cable de control de la antena motorizada o al
cable de fuente de alimentación del
amplificador de señal de la antena
cable de fuente de alimentación del
amplificador de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplificador de
señal de la antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de
control y de fuente de alimentación”.
señal de la antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de
control y de fuente de alimentación”.
A AMP REMOTE IN de un amplificador de
potencia opcional
potencia opcional
Esta conexión es sólo para amplificadores y una antena
motorizada. La conexión de cualquier otro sistema puede dañar la
unidad.
motorizada. La conexión de cualquier otro sistema puede dañar la
unidad.
A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa negro a
una superficie metálica del automóvil.
una superficie metálica del automóvil.
Al terminal de alimentación de +12 V que recibe
energía en la posición de accesorio del
interruptor de encendido
energía en la posición de accesorio del
interruptor de encendido
Notas
Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de
control y de fuente de alimentación”.
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Si el automóvil tiene una antena de FM/AM incorporada en el
cristal trasero o lateral, consulte “Notas sobre los cables de
control y de fuente de alimentación”.
Al terminal de alimentación de +12 V que recibe
energía sin interrupción
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa negro a
una superficie metálica del automóvil.
una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
El cable REM OUT (rayado azul y blanco) suministra cc +12 V al
encender la unidad.
Si el automóvil dispone de una antena de FM/AM incorporada en el
cristal trasero o lateral, conecte el cable REM OUT (rayado azul y
blanco) o el cable de fuente de alimentación auxiliar (rojo) al terminal
de alimentación del amplificador de señal de la antena existente. Para
obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin caja
de relé.
encender la unidad.
Si el automóvil dispone de una antena de FM/AM incorporada en el
cristal trasero o lateral, conecte el cable REM OUT (rayado azul y
blanco) o el cable de fuente de alimentación auxiliar (rojo) al terminal
de alimentación del amplificador de señal de la antena existente. Para
obtener más detalles, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin caja
de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito de la
memoria recibirá siempre alimentación, aunque apague el interruptor
de encendido.
Si conecta el cable de fuente de alimentación amarillo, el circuito de la
memoria recibirá siempre alimentación, aunque apague el interruptor
de encendido.
Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de
potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
No conecte el cable de conexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces activos
(con amplificadores incorporados) a los terminales de altavoz, puede
dañar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un
cable negativo común (–) para los altavoces derecho e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
unidad.
Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de
potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
No conecte el cable de conexión a masa de esta unidad al terminal
negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces activos
(con amplificadores incorporados) a los terminales de altavoz, puede
dañar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un
cable negativo común (–) para los altavoces derecho e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de
ambos dispositivos.
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de
ambos dispositivos.
L
R
REAR/SUB FRONT
AUDIO OUT
REAR / SUB
AUDIO OUT*
2
FRONT
AUDIO OUT
REMOTE
IN*
3
SIRIUSXM
IN
*
1
*
1
REM OUT
Max. supply current 0.4 A
Corriente máx. de alimentación
de 0,4 A
Corriente máx. de alimentación
de 0,4 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Con rayas azules y
blancas
Con rayas azules y
blancas
Red
Rojo
Rojo
ACC
Yellow
Amarillo
Amarillo
BATTERY
Black
Negro
Negro
Orange/white striped
Con rayas naranjas y blancas
Con rayas naranjas y blancas
ILLUMINATION
White
Blanco
Blanco
Green
Verde
Verde
Purple
Morado
Morado
White/black striped
Con rayas blancas y negras
Con rayas blancas y negras
Gray/black striped
Con rayas grises y negras
Con rayas grises y negras
Green/black striped
Con rayas verdes y negras
Con rayas verdes y negras
Gray
Gris
Gris
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
Purple/black striped
Con rayas moradas y negras
Con rayas moradas y negras
from car antenna (aerial)
desde la antena del
automóvil
desde la antena del
automóvil
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched SUB or REAR. For
details, see the supplied Operating Instructions.
*
3
Separate adaptor may be required.
*
4
not supplied
*
1
Cable con terminales RCA (no suministrado)
*
2
AUDIO OUT (salida de audio) puede cambiarse a
SUB o REAR. Para obtener informacion, consulte
el manual de instrucciones suministrado.
el manual de instrucciones suministrado.
*
3
Puede requerirse un adaptador independiente.
*
4
no suministrado
Satellite radio tuner
(SiriusXM)
*
4
Sintonizador de radio por satélite
(SiriusXM)
*
4
FRONT
AUDIO OUT
REAR / SUB
AUDIO OUT
A
TOYOTA
to dashboard/center console
al tablero o consola central
al tablero o consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
B
NISSAN
to dashboard/center console
al tablero o consola central
al tablero o consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Tamaño
5 × 8 mm máx.
5 × 8 mm máx.
size
5 × max. 8 mm
(
5 × max. 8 mm
(
7
/
32
× max.
5
/
16
in)
Tamaño
5 × 8 mm máx.
5 × 8 mm máx.
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
Precauciones
Elija cuidadosamente el lugar de montaje de forma que
la unidad no interfiera con las funciones normales de
conducción.
Evite instalar la unidad donde pueda quedar expuesta a
polvo, suciedad, vibraciones excesivas o altas
temperaturas, por ejemplo, a la luz solar directa o cerca
de conductos de calefacción.
Para realizar una instalación segura y firme, utilice
solamente elementos de instalación suministrados.
la unidad no interfiera con las funciones normales de
conducción.
Evite instalar la unidad donde pueda quedar expuesta a
polvo, suciedad, vibraciones excesivas o altas
temperaturas, por ejemplo, a la luz solar directa o cerca
de conductos de calefacción.
Para realizar una instalación segura y firme, utilice
solamente elementos de instalación suministrados.
Ajuste del ángulo de montaje
Ajuste el ángulo de montaje a menos de 45°.
Extracción del marco de
protección y del soporte
protección y del soporte
Antes de instalar la unidad, retire el marco de
protección
protección
y el soporte
de la unidad.
1
Retire el marco de protección
.
Apriete ambos bordes del marco de protección
y, a continuación, tire de él hacia fuera.
2
Retire el soporte
.
Inserte ambas llaves de liberación
entre la
unidad y el soporte
hasta que encajen.
Presione el soporte
y, a continuación,
levante la unidad para separar ambos
elementos.
elementos.
Nota
Antes de instalar esta unidad, extraiga el tornillo y el compartimento que
se encuentran en la parte posterior de la unidad. No utilice las piezas
anteriores que extrajo al instalar la unidad (
Antes de instalar esta unidad, extraiga el tornillo y el compartimento que
se encuentran en la parte posterior de la unidad. No utilice las piezas
anteriores que extrajo al instalar la unidad (
-3).
Ejemplo de montaje
Instalación en el tablero
Notas
Si es necesario, doble las uñas hacia fuera para que encaje firmemente
( -2).
Compruebe que los 4 enganches del marco de protección
Compruebe que los 4 enganches del marco de protección
estén
bien fijados en las ranuras de la unidad
( -3).
Montaje de la unidad en un
automóvil japonés
automóvil japonés
Es posible que no pueda instalar esta unidad en algunos
automóviles japoneses. En tal caso, consulte a su
distribuidor Sony.
automóviles japoneses. En tal caso, consulte a su
distribuidor Sony.
Nota
Para evitar que se produzcan fallas de funcionamiento, realice la
instalación solamente con los tornillos suministrados
Para evitar que se produzcan fallas de funcionamiento, realice la
instalación solamente con los tornillos suministrados
.
How to detach and attach the
front panel
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press and
hold
hold
. Press the front panel release
button, and pull it off towards you.
-B To attach
Engage part
of the front panel with part
of the unit,
as illustrated, and push the left side into position until it
clicks.
clicks.
Warning if your car’s ignition
has no ACC position
has no ACC position
Be sure to set the Auto Off function. For details, see the
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
supplied Operating Instructions.
The unit will shut off completely and automatically in the
set time after the unit is turned off, which prevents
battery drain.
If you do not set the Auto Off function, press and hold
until the display disappears each time
you turn the ignition off.
Fuse replacement
When replacing the fuse, be sure to
use one matching the amperage
rating stated on the original fuse.
If the fuse blows, check the power
connection and replace the fuse.
If the fuse blows again after
replacement, there may be an
internal malfunction. In such a case,
consult your nearest Sony dealer.
use one matching the amperage
rating stated on the original fuse.
If the fuse blows, check the power
connection and replace the fuse.
If the fuse blows again after
replacement, there may be an
internal malfunction. In such a case,
consult your nearest Sony dealer.
Forma de extraer e instalar el
panel frontal
panel frontal
Antes de instalar la unidad, extraiga el panel
frontal.
frontal.
-A Para extraerlo
Antes de extraer el panel frontal, asegúrese de mantener
presionado
presionado
. Presione el botón de
liberación del panel frontal y extraiga el panel frontal
hacia usted.
hacia usted.
-B Para instalarlo
Coloque la parte
del panel frontal en la parte
de la
unidad, como se muestra en la ilustración, y después
presione la parte izquierda hasta que encaje.
presione la parte izquierda hasta que encaje.
Advertencia: si el encendido
del automóvil no dispone de
una posición ACC
del automóvil no dispone de
una posición ACC
Asegúrese de ajustar la función de desconexión
automática. Para obtener más información, consulte el
manual de instrucciones suministrado.
La unidad se apagará completa y automáticamente en el
tiempo establecido después de que se desconecte la
unidad, lo que evita que se desgaste la batería.
Si no ha ajustado la función de desconexión automática,
mantenga presionado
automática. Para obtener más información, consulte el
manual de instrucciones suministrado.
La unidad se apagará completa y automáticamente en el
tiempo establecido después de que se desconecte la
unidad, lo que evita que se desgaste la batería.
Si no ha ajustado la función de desconexión automática,
mantenga presionado
cada vez que
apague el interruptor de encendido, hasta que la pantalla
desaparezca.
desaparezca.
Sustitución del fusible
Al sustituir el fusible, asegúrese de
utilizar uno cuyo amperaje coincida
con el especificado en el original. Si
el fusible se funde, verifique la
conexión de alimentación y
sustitúyalo. Si el fusible vuelve a
fundirse después de sustituirlo, es
posible que exista alguna falla de
funcionamiento interno. En tal caso,
consulte con el distribuidor Sony
más cercano.
utilizar uno cuyo amperaje coincida
con el especificado en el original. Si
el fusible se funde, verifique la
conexión de alimentación y
sustitúyalo. Si el fusible vuelve a
fundirse después de sustituirlo, es
posible que exista alguna falla de
funcionamiento interno. En tal caso,
consulte con el distribuidor Sony
más cercano.
Fusible (10 A)
Precautions
Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection
collar and the bracket
collar and the bracket
Before installing the unit, remove the protection
collar
collar
and the bracket
from the unit.
1
Remove the protection collar
.
Pinch both edges of the protection collar
, then
pull it out.
2
Remove the bracket
.
Insert both release keys
together between
the unit and the bracket
until they click.
Pull down the bracket
, then pull up the unit
to separate.
Note
Before installing this unit, remove the screw and box on the back of the
unit. Do not use the previous parts you removed when installing the unit
(
Before installing this unit, remove the screw and box on the back of the
unit. Do not use the previous parts you removed when installing the unit
(
-3).
Mounting example
Installation in the dashboard
Notes
Bend these claws outward for a tight fit, if necessary
( -2).
Make sure that the 4 catches on the protection collar
are properly
engaged in the slots of the unit
( -3).
Mounting the unit in a
Japanese car
Japanese car
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws
To prevent malfunction, install only with the supplied screws
.
Face the hook inwards.
El gancho debe encontrarse
en la parte interior.
El gancho debe encontrarse
en la parte interior.
1
2
3
Dashboard
Tablero
Tablero
Claws
Uñas
Uñas
A
B
1
2
Front panel release button
Botón de liberación del
panel frontal
Botón de liberación del
panel frontal
Fuse (10 A)
3
Screw
Tornillo
Tornillo
Box
Compartimento
Compartimento
Note: Refer to “DISTINGUISHING OF THE Wal-Mart MODEL” on
page 4 for Wal-Mart model.
Click on the first or last page to see other CDX-GT565UV / CDX-GT615UV service manuals if exist.