Read Sony CDX-G1170U / CDX-G3170UV Service Manual online
CDX-G1170U/G3170UV
6
Connection
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
ͬ
Front speaker*
1
*
2
White
White/black striped
Gray
Black
Yellow
Red
Blue/white striped (MAX 0.4A)
from a wired remote control
(not supplied)*
(not supplied)*
4
For details, see “Making
connections” (page 17).
connections” (page 17).
Gray/black striped
Green
Green/black striped
Purple
Purple/black striped
*
3
*
3
Subwoofer*
1
Power amplifier*
1
from a car antenna (aerial)
Rear speaker
*1*2
SECTION 2
GENERAL
This section is extracted
from operating instruction.
from operating instruction.
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the yellow and red power supply leads
only after all other leads have been connected.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
.
Installation
Before installing the unit, remove the protection
collar ͨ and the bracket ʓ from the unit.
collar ͨ and the bracket ʓ from the unit.
1
Pinch both edges of the protection collar
ͨ, then pull it out.
2
Insert both release keys ͧ until they
click, and pull down the bracket ʓ, then
pull up the unit to separate.
click, and pull down the bracket ʓ, then
pull up the unit to separate.
Removing the protection collar and the
bracket
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
ɞ To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
connect the yellow and red power supply leads.
ɟ To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɠ To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɡ To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Making connections
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Note
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
Front speaker
Subwoofer
Click on the first or last page to see other CDX-G1170U / CDX-G3170UV service manuals if exist.