Read Sony CDX-G1170U / CDX-G3170UV Service Manual online
CDX-G1170U/G3170UV
5
2. Confi rmation After Destination Setting
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Destination setting checking method:
1. In the state of source off (the clock is displayed on the liquid
1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons
in order of the [
in order of the [
4]
t [5] t [PAUSE 6] (press only the
[PAUSE 6] button for two seconds).
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Clock display
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following fi gure), enter
the destination setting value display mode by pressing the [
the destination setting value display mode by pressing the [
SCRL DSPL] button twice.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
System controller version
3. Confi rm the alphanumeric character of 12 digits of in liquid
crystal display is an value correctly input.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Destination code
12 digits
OP0
OP1
OP2
OP3
OP4
OP5
4. The resetting operation is executed by pressing the [
OFF
SRC] button for 1 second after the confi rming ends, and the
unit returns to the normal condition.
unit returns to the normal condition.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Display after reset
TEST DISCS
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Part No.
Description
3-702-101-01 DISC
(YEDS-18),
TEST
4-225-203-01 DISC
(PATD-012),
TEST
NOTE OF PERFORMING THE OPERATION CHECK
When performing the operation check in the state that is removed
the CD mechanism deck from the main unit, it is necessary to use
a long fl exible fl at cable.
When performing the operation check, use following fl exible fl at
cable.
When performing the operation check in the state that is removed
the CD mechanism deck from the main unit, it is necessary to use
a long fl exible fl at cable.
When performing the operation check, use following fl exible fl at
cable.
Part No.
Description
1-846-819-31
CABLE FLEXIBLE FLAT (27 CORE)
(Length: 150 mm)
NOTE OF REPLACING THE KEY BOARD
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
NOTE OF REPLACING THE IC602 AND IC1301 ON
THE MAIN BOARD
IC602 and IC1301 on the MAIN board cannot replace with single.
When these parts are damaged, replace the complete mounted
board.
THE MAIN BOARD
IC602 and IC1301 on the MAIN board cannot replace with single.
When these parts are damaged, replace the complete mounted
board.
CLEANING THE CONNECTORS
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 5) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 5) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
Notes
ˎ For safety, turn off the ignition before cleaning the
connectors, and remove the key from the ignition
switch.
switch.
ˎ Never touch the connectors directly with your fingers
or with any metal device.
and clean the connectors with
Click on the first or last page to see other CDX-G1170U / CDX-G3170UV service manuals if exist.