Read Sony CDX-G1170U / CDX-G3170UV Service Manual online
CDX-G1170U/G3170UV
4
NOTE OF REPLACING THE COMPLETE MAIN BOARD
OR SYSTEM CONTROLLER (IC501)
When the complete MAIN board or system controller (IC501) is
replaced, the destination setting is necessary.
OR SYSTEM CONTROLLER (IC501)
When the complete MAIN board or system controller (IC501) is
replaced, the destination setting is necessary.
1. Destination
Setting
Set destination according to the procedure below.
1-1. Setting the Destination Code
1. In the state of source off (the clock is displayed), enter the test
1. In the state of source off (the clock is displayed), enter the test
mode by pressing the buttons in order of the [
4]
t [5] t
[PAUSE 6] (press only the [PAUSE 6] button for two seconds).
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Clock display
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following fi gure), enter
the destination setting mode by pressing the buttons in order
of the [
the destination setting mode by pressing the buttons in order
of the [
>
M
SEEK+]
t [SEEK–
m
.
]
t [PUSH EN-
TER/MENU].
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
System controller version
3. Input the alphanumeric character of 12 digits of “F XXXXXX”
displayed on the liquid crystal display, and execute the destina-
tion setting.
tion setting.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Note: Refer to following “1-3. Entering the Destination Code” for opera-
tion method.
Destination code
12 digits
OP0
OP1
OP2
OP3
OP4
OP5
4. The resetting operation is executed by pressing the [
OFF
SRC] button for 1 second after the setting ends, and the unit
returns to the normal condition.
returns to the normal condition.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Display after reset
1-2. Display in Destination Setting Mode
(Displayed characters/values in the following fi gure are example)
(Displayed characters/values in the following fi gure are example)
Destination code
12 digits
OP0
OP1
OP2
OP3
OP4
OP5
1-3. Entering the Destination Code
•
•
Method of operation by main unit
1. Rotate the control dial, and select the alphanumeric character
of “0 to F”.
2. The digit advances by pressing the [PUSH ENTER/MENU] or
[
>
M
SEEK+] button.
The digit returns by pressing the [MODE
] or [SEEK–
m
.
] button.
3. The setting is completed by pressing the [PUSH ENTER/
MENU] button, then the display turns off, the initialization op-
eration is done, and the display returns to the clock display.
eration is done, and the display returns to the clock display.
•
Method of operation by remote commander
1. Press
the
[V] or [v] button, and select the alphanumeric char-
acter of “0 to F”.
2. The digit advances by pressing the [b] or [ENTER] button.
The digit returns by pressing the [B] button.
3. The setting is completed by pressing the [ENTER] button, then
the display turns off, the initialization operation is done, and
the display returns to the clock display.
the display returns to the clock display.
1-4. Destination Code
Model
OP5
OP4
OP3
OP2
OP1
OP0
CDX-G1170U
3
0
1
8
0
0
CDX-G3170UV
3
8
1
8
6
0
– Continued on next page –
Click on the first or last page to see other CDX-G1170U / CDX-G3170UV service manuals if exist.