STR-DA5600ES - Sony Audio Service Manual (repair manual). Page 23

HISTORY  MODE
The state that the set is used is memorized.
Procedure:
1.  While pressing the [MEMORY/ENTER] and [MUSIC] but-

tons, press the [

?/1

] button to turn on the power and “HIS-

TORY” is displayed.

2.  Each time the [

M] and [m] buttons of remote commander is 

pressed, the item is switched in order as follows.

Protector generation total count

PRCT_COUNT: xxxx

Operating time until generating fi rst 
time protector (active standby is 
contained)

TTL_TIME:xxxxH xxM

Main on time until generating fi rst 
time protector

TTL_MAIN:xxxxH xxM

Factor of generating fi rst time protec-
tor

PROTECT:xxxx

Sound fi eld in fi rst time protector

SF xxxx

Input selector in fi rst time protector

INPUT:xxxx

Input mode in fi rst time protector

INMODE:xxxx

Input under lock in fi rst time protector

DSEL:xxxx

Stream under input in fi rst time 
protector

STREAM:xxxx

Channel information in fi rst time 
protector

CONFIG:xxxx

State of headphone in fi rst time 
protector

HEADPHONE:xxxx

Volume in fi rst time protector

VOL:xxxx.xxdB

Muting in fi rst time protector

MUTING:xxxx

EQ setting value in fi rst time protector

FRT BASS:xxxx.xxdB
FRT TREB:xxxx.xxdB

CNT BASS:xxxx.xxdB
CNT TREB:xxxx.xxdB

SUR BASS:xxxx.xxdB
SUR TREB:xxxx.xxdB

FH BASS:xxxx.xxdB
FH TREB:xxxx.xxdB

Level collection value each channel 
in fi rst time protector

Lv FL/FR:xx.xx/xx.xx

Lv CT/SW:xx.xx/xx.xx

Lv SL/SR:xx.xx/xx.xx
Lv BL/BR:xx.xx/xx.xx
Lv LF/RH:xx.xx/xx.xx

Total operation time after the ship-
ment

TTL_P_ON:xxxxHxxM

Main zone power on time after the 
shipment

TTL_M_ON:xxxxHxxM

Number of times of the power on 
after the shipment

REBOX: xxxx

3.  The backup data of the history mode are not initialized with 

the “MEMORY CLEAR MODE”. Initialize it with a “SHIP 
MODE”.

DMPORT  TEST  MODE
Procedure:
1.  Connect the DMPORT check jig (Part No. J-2501-309-A) with 

the DMPORT jack (CN6701) on the NETWORK board.

2.  While pressing the [HDMI IN] and [A.F.D.] buttons, press the 

[

?/1

] button to turn on the main power.

3.  The message “DMPORT OK”appears on the fl uorescent indi-

cator tube and enter the DMPORT test mode (Confi rmation of 
communication line).

 

When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.

  Each time the [

>] button on the remote commander is 

pressed, the connect check and adaptor version check are 
switched.

 

Press the [

.] button on the remote commander, connected 

confi rmation of the DMPORT check jig is done again.

4.  To a pin-jack of the DMPORT check jig input information 

relevant to audio signal (sine-wave 1.0 Vrms) and composite 
video signal (white 100% 1.0 Vp-p, color bar, etc.).

5. Confi rm the output of speakers and monitor TV (Confi rmation 

of analog signal).

6.  To release from this mode, press the [

x] button on the remote 

commander. 

SIRIUS  FACTORY  TEST  MODE
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of 
SIRIUS antenna and output of audio signal that SIRIUS antenna 
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio 
signal.
Procedure:
1.  The SIRIUS antenna was connected, while pressing the 
 

[TUNING MODE] and [A.F.D.] buttons, press the [

?/1

] but-

ton to turn on the main power.

2.  Whenever the [DISPLAY] button is pressed, the Module ver-

sion, SSP version, Security processor version, Audio processor 
version, Firmware product ID, Firmware product sequence ID, 
Sirius ID are displayed, next the output of the audio signal of 
1 kHz L/R, 20 Hz L/R, 10 Hz L/R, noise L, noise R and stop 
tone are switched.