STR-DA5600ES - Sony Audio Service Manual (repair manual). Page 24

SPECIAL  MENU  MODE
Procedure:
1.  Press the [

?/1

] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], 

[MUSIC], [MOVIE/HD-D.C.S.] button in order, the message “MENU SPECIALIZED!” appears.

2.  Press the [

M

]/[

m

] buttons of the remote commander, the message “<<< SPECIAL >>>” appears.

3.  Press the [

,

] button of the remote commander, the item is appears.

4.  Each time the [

M

]/[

m

] buttons of the remote commander is pressed, the item is switched in order as follows.

 

Some items can change the content. Display the cursor by pressing the [

,

] button of the remote commander, and changing the content 

by pressing the [

M

]/[

m

] buttons of the remote commander, and fi x the content by pressing the [

<

] button of the remote commander 

when you want to change the content of the item.

5.  To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE/HD-

D.C.S.] button in order again, the message “MENU SPECIALIZE OFF” appears.

SYSTEM version display

SYSTEM VERSION X.XXX

X.XXX: System software version

MAIN Ucom version display

MAIN A56ES 

∗∗∗ vX. XX

∗∗∗: Destination 
X.XX: Main system controller software version

SUB Ucom version display

SUB COMMON C vX.XX

X.XX: Sub system controller software version

Video Ucom version display

Video Ucom Ver X. XX

X.XX: Video system controller software version

FAROUDJA version display

FAROUDJA Ver X. XX

X.XX: Video processor software version (main)

FAROUDJA (2nd) version display

FAROUDJA2nd Ver X.XX

X.XX: Video processor software version (2nd)

GUI CG-ROM version display

GUI CGROM Ver X. XX

X.XX: CG-ROM software version

DSP Ucom version display

DSP Ucom Ver X. XX

X.XX: DSP controller version

DSP serial fl ash version display

DSP SFLASH Ver X. XX

X.XX: DSP serial fl ash software version

DSP parallel fl ash version display

DSP PFLASH Ver X. XX

X.XX: DSP parallel fl ash version

IR learning Ucom version display

IR LEARNING Ver X. XX

X.XX: IR learning fi rmware version

Network processor version

NET 10A56COM Ver X. XX

X.XX: Network processor fi rmware version

DSP debug menu

< DSP DEBUG MENU >

Not used for the servicing

Network debug menu

< NETWORK DEBUG MENU >

Menu mode to enter MAC address display. If the [ENTER] but-
ton of the remote commander is pressed, entering the menu, 
and operating the following menu become possible.

MAC address display 
(Network debug menu)

MACXX:XX:XX:XX:XX:XX

XX:XX:XX:XX:XX:XX: MAC address

Network update check
(Network debug menu)

NET UPDATE CHECK?

If the [Enter] button of the remote commander is pressed, the 
checking result is displayed without connecting to network. 
“NET UPDATE CHK OK”: OK, “NET UPDATE CHK NG D”: 
DSP Ucom NG, “NET UPDATE CHK NG F1”: Faroudja1 NG, 
“NET UPDATE CHK NG F2”: Faroudja2 NG, “NET UPDATE 
CHK NG V”: Video Ucom NG, “NET UPDATE CHK NG L”: 
Learning Ucom NG, “NET UPDATE CHK NG M”: Main Ucom 
NG, “NET UPDATE CHK NG S”: Sub Ucom NG

PNX JTAG Update mode (Network 
debug menu)

JTAG UPDATE: XXX

XXX: ON or OFF

PNX polling and reset function 
(Network debug menu)

PNX POLL&RESET XXX

XXX: ON or OFF
Send a command regularly, and it is a function to reset when 
there is not reaction.

DMS on/off (Network debug menu)

DMS(ZONE4) XXX

Not used for the servicing

ZONE4 power and input (Network 
debug menu)

ZONE4:XXX INPUT:##

Not used for the servicing

DMR on/off (Network debug menu)

DMR XXX

XXX: ON or OFF

External control on/off (Network 
debug menu)

EXTERNAL CTRL XXX

XXX: ON or OFF

Network standby on/off (Network 
debug menu)

NETWORK STANDBY XXX

XXX: ON or OFF