Read Sony SS-AC3 Service Manual online
SS-AC3
5
2-4. LOUDSPEAKER 1.9 cm (ASSIST TWEETER) (SP1, SP2),
SPEAKER (2.5 cm) ASSY (MAIN TWEETER) (SP3)
Note 1: When replacing the loudspeaker 1.9 cm (assist tweeter) (SP1, SP2) and speaker (2.5 cm) assy
(main tweeter) (SP3), refer to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
3 Lift up the loudspeaker
1.9 cm (assist tweeter:
upper side) (SP1).
5 loudspeaker 1.9 cm
(assist
tweeter:
upper side) (SP1)
loudspeaker 1.9 cm (assist tweeter: upper side)
(SP1)
(SP1)
loudspeaker 1.9 cm
(assist tweeter:
upper side) (SP1)
“–” wire [black]
(assist tweeter:
upper side) (SP1)
“–” wire [black]
5 loudspeaker 1.9 cm
(assist
tweeter:
lower side) (SP2)
loudspeaker 1.9 cm
(assist tweeter:
lower side) (SP2)
“+” wire [gray]
(assist tweeter:
lower side) (SP2)
“+” wire [gray]
3 Lift up the loudspeaker
1.9 cm (assist tweeter:
lower side) (SP2).
speaker (2.5 cm) assy
(main tweeter)
(SP3)
(main tweeter)
(SP3)
packing (C)
boss
packing (C)
boss
convex
part
part
Note 2: When disassembling loudspeakers
1.9 cm (assist tweeter) (SP1, SP2),
place a stand etc. under tweeter assy
and be careful not to crush the convex
part of a speaker (2.5 cm) assy
(main tweeter) (SP3).
Note 10: When installing the loudspeakers 1.9 cm (assist tweeter)
(SP1, SP2), be sure to perform the polar check of "+" and
íWRPDNHLQWRWKHXSSHUOHIWVLGHDQGWRDWWDFKLW
as shown in the following figure.
Note 8: Check packing (C) not having
overlapped or not having run
aground.
Note 7: Do not touch
the convex part.
stand
stand
Note 11: Check that the connection mistake or insertion of a wire are not imperfect.
Note 12: Insert the terminal straightly.
Note 13: The arrangement of a wire should check that left side is gray and that right side is black.
Note 14: Check that a wire is on a speaker (2.5 cm) assy (main tweeter) (SP3).
Note 12: Insert the terminal straightly.
Note 13: The arrangement of a wire should check that left side is gray and that right side is black.
Note 14: Check that a wire is on a speaker (2.5 cm) assy (main tweeter) (SP3).
2 two screws (BVTP3 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: 1P
+RZWRLQVWDOOWKHORXGVSHDNHUFPDVVLVWWZHHWHU6363
,QVWDOOHGSRVLWLRQRISDFNLQJ&
1 terminal
[gray]
1 terminal
[black]
–,QQHUYLHZ–
–,QQHUERWWRPYLHZ–
–,QQHUYLHZ–
“+”
“–”
2 two screws (BVTP3 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: 1P
4 packing (C)
Note
9: The packing (C)
cannot
be
re-used.
Be sure to replace
it for new parts.
4 packing (C)
Note
9: The packing (C)
cannot
be
re-used.
Be sure to replace
it for new parts.
6 speaker (2.5 cm) assy
(main tweeter) (SP3)
loudspeaker 1.9 cm (assist tweeter: lower side)
(SP2)
(SP2)
Click on the first or last page to see other SS-AC3 service manuals if exist.