Read Sony HCD-SHAKE100 / HCD-SHAKE99 Service Manual online
HCD-SHAKE99/HCDSHAKE100
4
SECTION 1
SERVICING NOTES
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during
• Keep the temperature of the soldering iron around 270 °C
during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or
or
unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the
leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radiation
exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radiation
exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
This appliance is classifi ed as a CLASS 1 LASER product by
IEC60825-1:2007. This marking is located on the rear exterior.
IEC60825-1:2007. This marking is located on the rear exterior.
MODEL IDENTIFICATION
- BACK PANEL -
Model
Part No.
AR, AUS, E2, E51
4-479-318-0[]
US
4-479-318-1[]
MX
4-479-318-2[]
EA, MY, SAF
4-479-318-3[]
• Abbreviation
AR :
AR :
Argentina
model
AUS :
Australian
model
E2
: 120V AC area in E model
E51
: Chilean and Peruvian models
EA
: Saudi Arabia model
MX
: Mexican model
MY
: Malaysia model
SAF : South African model
PLAYABLE DISCS
• AUDIO
• AUDIO
CD
• CD-R/CD-RW/DVD-R/DVD-RW
–
–
audio
data
–
MP3
fi les that conforms to ISO9660 Level 1/Level 2, or
Joliet (expansion format).
Notes
• MP3 (MPEG 1 Audio Layer-3) is a standard format defi ned
• MP3 (MPEG 1 Audio Layer-3) is a standard format defi ned
by ISO (International Organization for Standardization) which
compresses audio data. MP3 fi les must be in MPEG 1 Audio
Layer-3 format.
compresses audio data. MP3 fi les must be in MPEG 1 Audio
Layer-3 format.
• The system can only play back MP3 fi les that have a fi le
extension of “.mp3”.
NOTE OF REPLACING THE IC001, IC002, IC105, IC106,
IC301 (HCDSHAKE100) AND IC302 (HCDSHAKE100)
ON THE MOTHERBOARD BOARD
IC001, IC002, IC105, IC106, IC301 (HCDSHAKE100) and
IC302 (HCDSHAKE100) on the MOTHERBOARD board cannot
exchange with single. When these parts on the MOTHERBOARD
board are damaged, exchange the entire mounted board.
IC301 (HCDSHAKE100) AND IC302 (HCDSHAKE100)
ON THE MOTHERBOARD BOARD
IC001, IC002, IC105, IC106, IC301 (HCDSHAKE100) and
IC302 (HCDSHAKE100) on the MOTHERBOARD board cannot
exchange with single. When these parts on the MOTHERBOARD
board are damaged, exchange the entire mounted board.
NOTE OF REPLACEMENT OF THE MS-476 BOARD
When the MS-476 board is defective, exchange the entire
LOADING COMPLETE ASSY (T).
When the MS-476 board is defective, exchange the entire
LOADING COMPLETE ASSY (T).
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of a demonstration disc
in the store is equipped.
The disc tray lock function for the antitheft of a demonstration disc
in the store is equipped.
Releasing Procedure:
1. Press
1. Press
[
\
/1
] button to turn the power on.
2. Press the [CD](SHAKE99)/[DVD/CD](HCDSHAKE100) button
to select CD/DVD function.
3. Press the [
x
] button and [
/+] button simultaneously and
hold down for around 5 seconds.
4. The message “UNLOCKED” is displayed and the disc tray is
unlocked.
Note: When
“
LOCKED
”
is displayed, the slot lock is not released by
turning power on/off with the
[
\
/1
]
button.
PART No.
Ver. 1.4
Click on the first or last page to see other HCD-SHAKE100 / HCD-SHAKE99 service manuals if exist.