Read Sony HBD-TZ145 Service Manual online
HBD-TZ145
3
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution:
about 350 °C.
Caution:
The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
ABOUT PART REPAIR OF EACH BOARD
When boards installed by this unit are defective, replace the com-
plete board. However, some of mounted parts are replaceable. Re-
fer to “5. ELECTRICAL PARTS LIST” (page 40) for parts that
can be replaceable.
When boards installed by this unit are defective, replace the com-
plete board. However, some of mounted parts are replaceable. Re-
fer to “5. ELECTRICAL PARTS LIST” (page 40) for parts that
can be replaceable.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Press the [
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Press the [
?/1
] button to turn on the system.
2. Press the [FUNCTION] button to select “DVD/CD”.
3. Insert
3. Insert
disc.
4. Press the [
x
] and [
Z
] buttons simultaneously and hold down
unit “LOCKED” displayed on the fluorescent indicator tube
(around 5 seconds).
(around 5 seconds).
Releasing Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the system.
2. Press the [FUNCTION] button to select “DVD/CD”.
3. Press the [
3. Press the [
x
] and [
Z
] buttons simultaneously and hold down
unit “UNLOCKED” displayed on the fluorescent indicator
tube (around 5 seconds).
tube (around 5 seconds).
Note:
When “LOCKED” is displayed, the disc tray lock is not released by
turning power on/off with the [?/1] button.
VERSION DISPLAY
Confi rmation procedure of version only:
1. Connect this unit with TV monitor.
2. Press the [
Confi rmation procedure of version only:
1. Connect this unit with TV monitor.
2. Press the [
?/1
] button to turn on the system.
3. Press the [
Z
] button.
(State of “Tray open”)
3. After press the [
x
] button, press the [ DISPLAY] button on
the remote commander.
4. The version information appears to the TV monitor.
(Displayed character/values are example)
Model NO.
Release: 2012.03.29A
MPEG: 3.22.24
MPEG: 3.22.24
Region: 0
MCU: 3.25.26
HdcpKey: Yes
DAV-TZ145 E12
OK
Releasing Procedure:
1. Press the [ ] button on the remote commander.
2. The system will return to normal mode.
1. Press the [ ] button on the remote commander.
2. The system will return to normal mode.
LASER DIODE AND FOCUS SEARCH
Procedure:
1. Open the case and turn POWER on with no disc inserted.
2. Confi rm that the following operation is performed while ob-
Procedure:
1. Open the case and turn POWER on with no disc inserted.
2. Confi rm that the following operation is performed while ob-
serving the objecting lens from the clearance of DVD mecha-
nism deck.
nism deck.
Confi rm that laser beam is spread.
Up and down motion of the objective lens. (2 times)
ON CLEANING DISCS, DISC/LENS CLEANERS
Do not use cleaning discs or disc/lens cleaners (including wet or
spray types). These may cause the apparatus to malfunction.
Do not use cleaning discs or disc/lens cleaners (including wet or
spray types). These may cause the apparatus to malfunction.
IMPORTANT NOTICE
Caution: This system is capable of holding a still video image or on-
screen display image on your television screen indefi nitely. If you leave
the still video image or on-screen display image displayed on your TV
for an extended period of time you risk permanent damage to your tele-
vision screen.
Projection televisions are especially susceptible to this.
Caution: This system is capable of holding a still video image or on-
screen display image on your television screen indefi nitely. If you leave
the still video image or on-screen display image displayed on your TV
for an extended period of time you risk permanent damage to your tele-
vision screen.
Projection televisions are especially susceptible to this.
ABOUT “PROTECT” DISPLAY
If any one of the speakers is not connected, “PROTECT” may be
displayed. This is a specifi cation of this unit. When performing an
inspection for which disc playback is necessary, connect all of the
speakers.
If any one of the speakers is not connected, “PROTECT” may be
displayed. This is a specifi cation of this unit. When performing an
inspection for which disc playback is necessary, connect all of the
speakers.
Click on the first or last page to see other HBD-TZ145 service manuals if exist.