Read Sharp VC-MH731HM (serv.man10) User Guide / Operation Manual online
8
INSTALLING YOUR VCR
AUTO INSTALLATION
9. Press [
] to select SAT NO. Turn to the table at the end of this manual. Look for
the make of your satellite receiver and use the NUMBER BUTTONS to enter the first
code number listed. For example number 8 should be entered 0 0 8. Your satellite
should now change to preset channel 12.
code number listed. For example number 8 should be entered 0 0 8. Your satellite
should now change to preset channel 12.
10.If your satellite receiver has changed to preset channel 12, the VCR will automatically
install both satellite and terrestrial channels. Press SET to confirm.
11.The VCR will attempt to copy the TV preset list (NexTView, Smart Link, Easy Link and
Megalogic compatible TV’s only). During the copying process the display will show
the TV presets that are being copied. If the VCR is unable to copy the TV preset list the
terrestrial and satellite channels will be automatically installed. (Auto install may take a
few minutes.) On completion the MOVE
the TV presets that are being copied. If the VCR is unable to copy the TV preset list the
terrestrial and satellite channels will be automatically installed. (Auto install may take a
few minutes.) On completion the MOVE
menu will appear showing the preset
channel order. Press MENU to exit. If the clock is not automatically set, the clock screen
will appear, refer to MANUALLY SETTING THE CLOCK. To check the clock has been
set correctly, press DISPLAY until the time appears on the display. If you wish to customise
will appear, refer to MANUALLY SETTING THE CLOCK. To check the clock has been
set correctly, press DISPLAY until the time appears on the display. If you wish to customise
the channel order refer to MANUALLY SORTING CHANNELS.
/
All the programmes should now be correctly tuned in and the clock set.
If you connect a satellite receiver to the VCR
for the first time, after auto-installation, see
SATELLITE RECEIVER / CABLE BOX INSTALLATION.
If you
replace your satellite receiver, you will need to follow the complete auto-
installation procedure to tune your VCR to the satellite receiver. This is because your
new satellite receiver will not over-write the previous satellite channels in your VCR.
NOTES:
●
If your satellite receiver has not changed to preset channel 12 enter the next code
number on the list. Continue until the receiver shows preset channel 12, then continue
from point 10.
number on the list. Continue until the receiver shows preset channel 12, then continue
from point 10.
●
If your satellite receiver is not listed at the end of this manual or after entering all the
numbers listed for your receiver, the satellite receiver preset channel has still not changed
to 12, enter 0 0 1, and look to see if the satellite receiver has changed to preset
channel 12. If it has, continue from point 10. If not, press
numbers listed for your receiver, the satellite receiver preset channel has still not changed
to 12, enter 0 0 1, and look to see if the satellite receiver has changed to preset
channel 12. If it has, continue from point 10. If not, press
to select 0 0 2 and re-
check. Continue until your receiver changes to preset 12, then continue from point 10.
●
If there is still no response from your satellite receiver, try adjusting its position to
improve the Infa Red VCR to satellite receiver reception.
improve the Infa Red VCR to satellite receiver reception.
●
Auto-installation will stop when the satellite receiver reaches preset channel 99, or when
all the 84 VCR preset channels have been used.
all the 84 VCR preset channels have been used.
●
The VCR will place all found terrestrial channels starting at preset 1, then all satellite
channels from the first available preset channel after the terrestrial channels.
channels from the first available preset channel after the terrestrial channels.
vc-m331/mh731hm 3/2/99 1:34 pm Page 12
Click on the first or last page to see other VC-MH731HM (serv.man10) service manuals if exist.