LC-32GA6E (serv.man5) - Sharp TV User Guide / Operation Manual. Page 20

You can select the display size by pressing f on the remote
control.

• “WIDE MODES” cannot be set when the FM radio mode is

selected.

E

Press f to display the “WIDE MODES” screen.

Press a/b to select “WIDE MODES”, and then press
c/d to select your desired screen size format.

NORMAL 4:3: For 4:3 “standard” pictures. A side bar appears

on each side.

CINEMA: For 16:9 broadcast cinema movies, etc. Bars may

appear on the top and bottom with some programmes.

ZOOM 14:9: A thin side bar appears on each side, and you

may also see bars on the top and bottom with some
programmes.

PANORAMA: In this mode the picture is progressively stretched

toward each side of the screen.

FULL: For 16:9 squeeze pictures.
AUTO: In this mode the screen size changes automatically.

When you select “CINEMA”, “ZOOM 14:9” or “PANORAMA”,
you can change the vertical “SIZE” and vertical “POSITION”.

1 Perform steps 1 and 2 on the above to select “CINEMA”,

“ZOOM 14:9” or “PANORAMA”.

2 Press a/b to select “SIZE” or “POSITION”. The “SIZE”

or “POSITION” indicator displays.

3 Press c/d to adjust the item to your desired size and

position.

4 Press OK if you wish to normalize the vertical “SIZE” or

vertical “POSITION”.

5 Press END to exit.

E

Some broadcasting stations send the WSS signal with
information of original screen size. When the TV is in “AUTO”
mode and receives the WSS signal, it changes the screen
size automatically.

Press f to display the “WIDE MODES” screen.

Press a/b to select “WIDE MODES”, and then press
c/d to select “AUTO”.

• When you are watching the TV through the external sources

(EXT1 or EXT2), and it receives information of 16:9 format
(through the audio-video control pin) the TV selects “FULL”
automatically.

• In order for the “AUTO” to function correctly, the “WSS”

item must be set “ON” in the “GENERAL SETUP” menu.
To check it, see page 17.

• When the TV does not receive the WSS code, it changes

automatically to “PANORAMA”.

Teletext broadcasts pages of information and entertainment
to specially equipped television sets. Your TV receives
Teletext signals broadcast by the TV network, and decodes
them into graphical format for viewing. News, weather and
sports information, stock exchange prices and programme
previews are among the many services available.

Select a TV channel or external input source providing
the Teletext programme.

Press m  to display the Teletext on the left screen and
normal image on the right screen.

Press  m again to display the Teletext on the whole
screen.

Press m again to display the normal image only.

Increase or decrease the page number.

Select a group or block of pages displayed in
the coloured  brackets at the bottom of the
screen by pressing the corresponding
Colour (Red/Green/Yellow/Blue) on the
remote control unit.

Directly select any page from 100 to 899 by
using 0–9.

Switch the Teletext image to Full, Upper half
or Lower half.

Reveal or hide hidden information such as an
answer to a quiz.

Stop updating Teletext pages automatically or
release the hold mode.

Display the subtitle or exit the subtitle screen.
• Subtitle will not be displayed when the

service does not contain the subtitle
information.

• If multiple subtitle pages are broadcast,

press  [ again to display the additional
subtitle pages.

Reveal or hide subpages.
• Red: Move to the previous subpage.
• Green: Move to the following subpage.
• These two buttons are shown on the screen

by the signs f and e.

• The number “3979” (is not related to

subpages) may display in some cases. (This
is not a problem)

P (r/s)

f
(WIDE MODES)

k (Reveal)

3 (Hold)

[ (Subtitle)

1 (Subpage)

WSS code 16:9

CINEMA

WSS code 14:9

ZOOM 14:9

WSS code 4:3

NORMAL 4:3

LC-26/32/37GA6E(E)_c

05.6.29, 7:50 AM

20